Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1993 BMW 318IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 318IS cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 1993 BMW 318IS 1.8 L4 GAS
- Connect suitable pressure bleeder to brake fluid reservoir. Maximum charging pressure is 43.5 psi.
- Attach bleeder hose and container to right rear wheel. Bleed until no bubbles appear.
- Repeat step 2 for left rear, right front and left front wheels.
- Support rear suspension at wheel carriers and lower car so rear suspension compresses to its normal loaded position (to prevent damage to output shaft joints). Wheels must be able to turn freely.
- Attach...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 318IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 318IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 318IS cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description -> 735 & 750 -> 850 -> H-31 Hydraulic System -> Master Cylinder
Vehicle: 1993 BMW 318IS 1.8 L4 GAS
H-31 Hydraulic System
The H-31 hydraulic system, Fig. , incorporates a power flow regulator which diverts a small flow of fluid from the power steering operating circuit for the power assisted brake system. It charges the hydraulic reservoir in a high pressure range without impairing the function of power steering. The pressurized hydraulic oil volume is supplied to the booster for the sake of power assistance and is applied by operating the connected standard tandem master cylinder. should the power steering pump fail, the hydraulic reservoir has sufficient reserve pressure to permi...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 318IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 318IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 318IS cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting
Vehicle: 1993 BMW 318IS 1.8 L4 GAS
Refer to "Diagno... "
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 318IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 318IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 318IS cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> 318 & 325 -> 735, 750 & 850 -> Brake Force Regulator, Replace -> Master Cylinder, Replace -> Power Flow Regulator, Replace
Vehicle: 1993 BMW 318IS 1.8 L4 GAS
Master Cylinder, Replace
- Remove brake fluid from master cylinder with a syringe.
- Remove plug and clutch hose if equipped.
- Remove fluid reservoir.
- Remove brake lines, then mounting bolts.
- Remove master cylinder.
- Reverse procedure to install and bleed brake system.
Power Flow Regulator, Replace
735, 750 & 850
- With engine off, discharge hydraulic reservoir by operating brake pedal approximately 20 times with same force required for full stop braking action.
- Disconnect electri...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 318IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 318IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 318IS cars and light trucks from 1990+.
Anti-lock Brakes -> Description
Vehicle: 1993 BMW 318IS 1.8 L4 GAS
The Anti-Lock Brake System (ABS) consists of a control unit, hydraulic unit, speed sensors and wiring harness. Each speed sensor has a gear wheel which runs past the permanently magnetized edge of the speed sensor installed in the wheel hub. The rotary motion of the wheels is recorded by inductive sensors and an electric signal is sent to the electronic control unit.
The electronic control unit is located in a compartment on the right side of the engine compartment. This control unit inputs acceleration, deceleration and slip factors from the electronic speed sensors, which are propo...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 318IS BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 318IS AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 318IS cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Caliper Overhaul -> Caliper, Replace -> Front -> Rear
Vehicle: 1993 BMW 318IS 1.8 L4 GAS
Caliper, Replace
Front
- Raise and support vehicle, then remove front wheel.
- Drain a moderate amount of brake fluid from reservoir with a syringe.
- Disconnect caliper brake hose.
- Remove caliper bolts and disconnect brake pad wear sensor electrical connector, if necessary.
- Remove caliper toward rear.
- Reverse procedure to install, noting the following:
- Tighten bolts to specifications.
- Bleed brake system.
- Ensure brake pad wear sensor wire does not contact rotor or wheel.
Rear
- Raise and support vehicle, then remove wheel.
- Drain a moderate amount of brake fluid from reservoir with a syringe.
- Disconne...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 318IS BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1993 BMW 318IS vehicle. |
Access the Complete guide! |