Auto Parts Search
We have info for following modifications of 1992 Porsche 911
- 1992 Porsche 911 3.6 H6 GAS, CC:3606, Fuel Injection, Engine VIN:, Desg:B
- 1992 Porsche 911 Carrera 3.6 H6 GAS, CC:3606, Fuel Injection, Engine VIN:, Desg:B
- 1992 Porsche 911 Carrera 4 3.6 H6 GAS, CC:3606, Fuel Injection
- 1992 Porsche 911 Turbo Look 3.6 H6 GAS, CC:3606, Fuel Injection, Engine VIN:, Desg:B
- 1992 Porsche 911 Turbo 3.3 H6 GAS, CC:3294, Fuel Injection, Engine VIN:, Desg:A
BRAKE SERVICE PROCEDURES FOR 1992 Porsche 911 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Porsche 911 cars and light trucks from 1990+.
PORSCHE, POWER BRAKE UNITS -> POWER BRAKE UNITS -> BRAKE BOOSTER REPLACEMENT -> 911 -> 928 -> 944
Vehicle: 1992 Porsche 911 Carrera 4 3.6 H6 GAS
911
- Remove brake booster operating rod lockpin.
- Remove master cylinder attaching bolt from luggage compartment floor plate.
- Drain brake fluid reservoir.
- Disconnect electrical connectors for stop light switch, then disconnect vacuum hose at brake booster and the brake lines at master cylinder.
- Remove brake booster brace upper attaching bolt and the booster base attaching nuts, then remove master cylinder and booster as an assembly. Brace and operating rod do not have to be disconnected at pedal assembly to remove brake booster.
- Reverse procedure to install, noting the followi...
CLICK HERE TO GET FULL ACCESS TO 1992 Porsche 911 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Porsche 911 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Porsche 911 cars and light trucks from 1990+.
PORSCHE, ANTI-LOCK BRAKES -> COMPONENT REPLACEMENT -> 944 -> ELECTRONIC CONTROL UNIT, REPLACE -> HYDRAULIC UNIT, REPLACE
Vehicle: 1992 Porsche 911 3.6 H6 GAS
These components are non-serviceable and must be replaced as a unit.
HYDRAULIC UNIT, REPLACE
- Disconnect battery ground cable.
- Mark respective positions of wheel and wheel hub for reassembly, then remove right front wheel assembly.
- Remove wheel-arch inner panel.
- On 944S and 944 Turbo, disconnect braking-force regulator.
- Disconnect all brake lines, numbers one through six from hydraulic unit.
- On all models, disconnect ground wire, then remove mounting bolts from hydraulic-unit holder.
- Move hydraulic unit and holder out slightly to gain access to strain relief for 12-pole plug (no. t...
CLICK HERE TO GET FULL ACCESS TO 1992 Porsche 911 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Porsche 911 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Porsche 911 cars and light trucks from 1990+.
PORSCHE, POWER BRAKE UNITS -> POWER BRAKE UNITS -> BRAKE BOOSTER REPLACEMENT -> 911 -> 928 -> 944
Vehicle: 1992 Porsche 911 Turbo Look 3.6 H6 GAS
911
- Remove brake booster operating rod lockpin.
- Remove master cylinder attaching bolt from luggage compartment floor plate.
- Drain brake fluid reservoir.
- Disconnect electrical connectors for stop light switch, then disconnect vacuum hose at brake booster and the brake lines at master cylinder.
- Remove brake booster brace upper attaching bolt and the booster base attaching nuts, then remove master cylinder and booster as an assembly. Brace and operating rod do not have to be disconnected at pedal assembly to remove brake booster.
- Reverse procedure to install, noting the followi...
CLICK HERE TO GET FULL ACCESS TO 1992 Porsche 911 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Porsche 911 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Porsche 911 cars and light trucks from 1990+.
PORSCHE, DISC BRAKES -> PARKING BRAKE ADJUSTMENT -> 911 -> 928 -> 944
Vehicle: 1992 Porsche 911 Turbo Look 3.6 H6 GAS
911
- Raise and support vehicle.
- Remove rear wheels.
- Release brake cable tension at adjusting nuts behind disc splash shield.
- Insert screwdriver into adjustment opening in rear brake disc assembly.
- Rotate parking brake adjustment sprocket so that disc can no longer be rotated by hand.
- Repeat step 5 on opposite side.
- Adjust cable tension until slack is removed by rotating adjustment nuts behind brake disc splash shield.
- Remove tunnel cover and parking brake lever boot and check position of cable equalizer.
- Position the equalizer in the two inspection holes when lever is pulled up.
- T...
CLICK HERE TO GET FULL ACCESS TO 1992 Porsche 911 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Porsche 911 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Porsche 911 cars and light trucks from 1990+.
PORSCHE, ANTI-LOCK BRAKES -> DIAGNOSIS & TESTING
Vehicle: 1992 Porsche 911 Carrera 4 3.6 H6 GAS
The electrical control unit has a self-diagnosis testing facility. For this reason, it is not possible or necessary to check the control unit unless the check is carried out as part of an ABS test required for other reasons and only when this test is carried out with the Bosch K7-ETT 016.00/VAG 1516 test equipment.
After any work on the braking system which did not affect parts directly involved in the ABS, a function test check is required. The pi...
CLICK HERE TO GET FULL ACCESS TO 1992 Porsche 911 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Porsche 911 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Porsche 911 cars and light trucks from 1990+.
PORSCHE, ANTI-LOCK BRAKES -> DIAGNOSIS & TESTING
Vehicle: 1992 Porsche 911 Carrera 3.6 H6 GAS
The electrical control unit has a self-diagnosis testing facility. For this reason, it is not possible or necessary to check the control unit unless the check is carried out as part of an ABS test required for other reasons and only when this test is carried out with the Bosch K7-ETT 016.00/VAG 1516 test equipment.
After any work on the braking system which did not affect parts directly involved in the ABS, a function test check is required. The pi...
CLICK HERE TO GET FULL ACCESS TO 1992 Porsche 911 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1992 Porsche 911 vehicle. |
Access the Complete guide! |