Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1991 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Infiniti G20 cars and light trucks from 1990+.
INFINITI, ANTI-LOCK BRAKES -> COMPONENT REPLACEMENT -> ACTUATOR -> ACTUATOR RELAYS -> G20 -> SPEED SENSORS
Vehicle: 1991 Infiniti G20 2.0 L4 GAS
SPEED SENSORS
When replacing speed sensors refer to Figs. through .
ACTUATOR
- Disable airbag system as outlined under "Airbag System Disarming."
- Drain brake fluid by attaching hose to each wheel cylinder, then open each bleeder valve while depressing brake pedal.
- Mark each brake pipe connector for proper installation.
- Disconnect electrical connector, brake pipes, then attaching nuts.
- Remove actuator.
- Re...
CLICK HERE TO GET FULL ACCESS TO 1991 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Infiniti G20 cars and light trucks from 1990+.
INFINITI, DISC BRAKES -> SERVICE -> Adjust -> BRAKE PAD REPLACE -> BRAKE PEDAL, ADJUST -> CALIPER -> Disassemble -> EXCEPT G20 REAR -> G20 -> G20 REAR -> M30 & Q45 -> PARKING BRAKE SHOES -> Replace
Vehicle: 1991 Infiniti G20 2.0 L4 GAS
BRAKE PAD REPLACE
- Raise and support vehicle, then remove master cylinder cap.
- On Q45 models, disconnect speed sensor connector.
- On all models, remove lower caliper mounting pin/bolt.
- Pivot caliper upwards. Remove pad retainers and inner and outer shims. Fig. .
- Remove brake pads.
- Compress caliper piston with suitable C-clamp.
- Reverse procedure to install. Torque to specifications and bleed brake system.
CALIPER
EXCEPT G20 REAR
Replace
- Raise and support vehicle, then remove caliper mounting pins/bolts.
- Disconnect brake hose and remove caliper.
- Reverse procedure to install. Torque to specifications and...
CLICK HERE TO GET FULL ACCESS TO 1991 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Infiniti G20 cars and light trucks from 1990+.
INFINITI, DISC BRAKES -> TIGHTENING SPECIFICATIONS -> G20 -> M30 & Q45
Vehicle: 1991 Infiniti G20 2.0 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 1991 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Infiniti G20 cars and light trucks from 1990+.
INFINITI, ANTI-LOCK BRAKES -> TROUBLESHOOTING
Vehicle: 1991 Infiniti G20 2.0 L4 GAS
Refer to Figs. and , for system symptom ch...
CLICK HERE TO GET FULL ACCESS TO 1991 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Infiniti G20 cars and light trucks from 1990+.
INFINITI, ANTI-LOCK BRAKES -> SELF-DIAGNOSIS & TESTING -> DIAGNOSTIC TESTS -> G20 -> M30 -> Q45
Vehicle: 1991 Infiniti G20 2.0 L4 GAS
The warning lamp on the instrument panel will come on when a problem is detected in the ABS braking system. To obtain a self diagnosing result the vehicle must be driven for at least one minute at a minimum speed of 20 mph before self diagnosis is obtained. After vehicle is stopped, the number of LED flashes is counted with the engine running, Fig. .
The LED, which is located in the control unit identifies a problem by the number of flashes, Figs and The LED and warning lamp will stay activated, even after malfunct...
[[table data]] [[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 1991 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1991 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1991 Infiniti G20 cars and light trucks from 1990+.
INFINITI, POWER BRAKE UNITS -> POWER BOOSTER REPLACEMENT
Vehicle: 1991 Infiniti G20 2.0 L4 GAS
- Connect tube to bleeder valve.
- Open bleeder valve, drain fluid by depressing brake pedal until master cylinder is empty.
- Remove brake line flare nuts, then master cylinder attaching nuts.
- Remove clevis pin, Figs. and .
- Remove brake booster attaching nuts, then remove booster.
- Reverse procedure to install noting ...
CLICK HERE TO GET FULL ACCESS TO 1991 Infiniti G20 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1991 Infiniti G20 vehicle. |
Access the Complete guide! |