Auto Parts Search
Mazda 5 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Mazda REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Year
2010 | 2009 | 2008 | 2007 |
2006 |
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about Mazda 5 car and truck repair procedures including Mazda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up & drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your Mazda 5 automobile. Try the Automotix DIY solution today!
FUEL FILTER REPLACEMENT PROCEDURES FOR Mazda 5 AUTOMOBILES
Fuel filter replacement procedures with corresponding images for most domestic and imported Mazda 5 cars and light trucks sold in the U.S. for 1980+.
Mazda -> Fuel Filter Scheduled Maintenance -> 2003-06 Except B-Series & Tribute -> Normal Service -> Severe Service
Vehicle: 2006 Mazda 5 Sport 2.3 L4 GAS
Normal Service
Se...
CLICK HERE TO GET FULL ACCESS TO Mazda 5 FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR Mazda 5 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported Mazda 5 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2009 Mazda 5 Grand Touring 2.3 L4 GAS
Performing the following procedures without first removing the ABS wheel-speed sensor may possibly cause an open circuit in the wiring harness if pulled by mistake. Before performing the following procedures, disconnect the ABS wheel speed sensor connector (axle side) and fix the wiring harness to an appropriate place where it will not be pulled by mistake while servicing vehicle.
Note: When replacing the driveshaft (double offset joint type), replace it as a single unit because it cannot be disassembled.
- Raise and support vehicle and support it with safety stands in proper...
CLICK HERE TO GET FULL ACCESS TO Mazda 5 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR Mazda 5 AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported Mazda 5 cars and light trucks sold in the U.S. from mid 1990's+.
Reset Procedures
Vehicle: 2009 Mazda 5 Grand Touring 2.3 L4 GAS
Adjust the tire to the recommended pres...
CLICK HERE TO GET FULL ACCESS TO Mazda 5 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR Mazda 5 AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported Mazda 5 cars and light trucks from 1990+.
Alternator, Replace
Vehicle: 2006 Mazda 5 Touring 2.3 L4 GAS
- Unhook battery cover from battery box.
- Disconnect battery ground cable.
- Raise vehicle on lift.
- Remove engine undercover bolts and splash shield as a single unit.
- Remove plug hole plate by lifting up on rubber clips with suitable tool.
- Remove and discard drive belt.
- Lift coolant reservoir from mounting bracket and disconnect hose.Drain coolant in a clean container to catch coolant after removing hose. Lay coo...
CLICK HERE TO GET FULL ACCESS TO Mazda 5 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR Mazda 5 AUTOMOBILES
Cabin air filter locations and replacement procedures with corresponding images for most domestic and imported Mazda 5 cars and light trucks sold in the U.S. as equipped to the current model year.
Cabin Air Filter Service -> Mazda -> Mazda5
Vehicle: 2009 Mazda 5 Sport 2.3 L4 GAS
Under normal operating conditions the cabin air filter should be replaced every 24 months or 25,000 miles. In dusty areas change the cabin air filter more often.
- Disconnect the battery ground cable.
- Remove the undercover.
- Disconnect the evaporator temperature sensor electrical connector.
- Remove the power MOS FET connector.
- Remove...
CLICK HERE TO GET FULL ACCESS TO Mazda 5 CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR Mazda 5 AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported Mazda 5 cars and light trucks sold in the U.S. from 1990+.
Mazda -> Tire Pressure Monitoring System Indicator -> 2006-09 Mazda5 -> Relearn -> Reset
Vehicle: 2006 Mazda 5 Touring 2.3 L4 GAS
Reset
Adjust the tire to the recommended pressure, then drive the vehicle to reset the warning lamp.
Relearn
After changing a tire, cycle the ignition switch to the On position and then retu...
CLICK HERE TO GET FULL ACCESS TO Mazda 5 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR Mazda 5 AUTOMOBILES
Includes radiator, cooling and heater hose replacement procedures for domestic and imported Mazda 5 cars and light trucks from 1990+
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2009 Mazda 5 Touring 2.3 L4 GAS
Lower
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at radiator outlet.
- Remove hose from radiator.
- Reposition hose clamp at water inlet.
- Remove hose from water inlet.
- Remove hose from vehicle.
- Reverse procedure t...
CLICK HERE TO GET FULL ACCESS TO Mazda 5 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR Mazda 5 AUTOMOBILES
Serpentine belt replacement procedures with corresponding images for most domestic and imported Mazda 5 cars and light trucks sold in the U.S. from 1990+.
Serpentine Drive Belt, Replace -> A/C Compressor Drive Belt -> Alternator Drive Belt
Vehicle: 2010 Mazda 5 Sport 2.3 L4 GAS
A/C Compressor Drive Belt
- Remove engine under cover and splash shield.
- Remove A/C Compressor Drive Belt with suitable scissors. A/C Compressor Drive Belt cannot be reused.
- Install new drive belt to A/C compressor pulley.
- Rotate crankshaft pulley clockwise, using a suitable tool and install ...
CLICK HERE TO GET FULL ACCESS TO Mazda 5 SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR Mazda 5 AUTOMOBILES
Component location diagrams for most Mazda 5 cars and light trucks sold in the U.S. from 1990+.
Body Harness Diagram for 2006 Mazda 5 Touring 2.3 L4 GAS Components on diagram: |
Engine Compartment Diagram for 2007 Mazda 5 Grand Touring 2.3 L4 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO Mazda 5 PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR Mazda 5 AUTOMOBILES
OEM drawn wiring diagrams for most Mazda 5 cars and light trucks sold in the U.S.
2008 Mazda 5 Grand Touring 2.3 L4 GAS Wiring Diagram Components on diagram: |
2007 Mazda 5 Grand Touring 2.3 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO Mazda 5 WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR Mazda 5 AUTOMOBILES
OEM TSB listings for most Mazda 5 cars and light trucks sold in the U.S. from 1985+.
Document: CLIMATE CONTROL UNIT BULB REPLACEMENT Vehicle: 2007 Mazda 5 Sport 2.3 L4 GAS Auto Systems: |
Document: ENGINE COMPARTMENT SHROUD PANEL POOR APPEARANCE Vehicle: 2007 Mazda 5 Sport 2.3 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO Mazda 5 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR Mazda 5 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most Mazda 5 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most Mazda 5 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most Mazda 5 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most Mazda 5 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO Mazda 5 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your Mazda 5 vehicle. |
Access the Complete guide! |