Auto Parts Search
2009 KIA Borrego CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT KIA REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 KIA Borrego AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2009 KIA Borrego EX 3.8 V6 GAS
- Raise and support vehicle.
- Remove wheel lug nuts.
- Remove split pin, then remove castle nut and washer from front hub.
- Remove mounting bolt of rear lower arm and rear carrier, while supporting lower arm with a jack.
- Remove spring, upper pad and lower pad.
- Remove shock absorber.
- Remove assist arm and trailing arm from rear axle carrier.
- Remove rear stabilizer li...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Borrego DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA Borrego AUTOMOBILES
Relearn Procedures -> Tire Pressure Sensor Initiation -> TPMS Receiver
Vehicle: 2009 KIA Borrego LX 3.8 V6 GAS
Tire Pressure Sensor Initiation
- Using Kia TPMS exciter tool, or equivalent, read the four tire pressure sensor IDs starting with sensor 1 the LH front wheel.
- Read the remaining sensors in the following order:
- Sensor 2, RH front wheel.
- Sensor 3, LH rear wheel.
- Sensor 4, RH rear wheel.
- Connect the Kia exciter tool, or equivalent, to the DLC (Data Link Connector) located under the LH side of the instrument panel.
- Using the tool, register the four sensor IDs to the TPMS receiver.
- Disconnect the tool from the DLC.
- Place the ignition switch in the Off position for 3 minutes, then turn the i...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Borrego TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2009 KIA Borrego AUTOMOBILES
Starter, Replace
Vehicle: 2009 KIA Borrego EX 3.8 V6 GAS
- Disconnect battery ground cable.
- Remove lefthand engine mounting bracket nut.
- Lift up engine assembly slightly by using a jack to get access to side of engine.
- Remove engine support bracket and starter protector.
- Disconnect starter cable from B+ terminal on solenoid, then disconnect connector from S terminal.
- ...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Borrego STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2009 KIA Borrego AUTOMOBILES
Cabin Air Filter Service -> Kia -> 2009 Borrego
Vehicle: 2009 KIA Borrego LX 3.8 V6 GAS
Under normal operating conditions the cabin air filter should be replaced every 9,320 miles. In dusty areas change the cabin air filter more often.
- Open the glove compartment.
- Remove the glove compartment stops located at each side, then lower the glove compartment, Fig. .
- Disconnect the glove compartment damper.
- Remove the cabin...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Borrego CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 KIA Borrego AUTOMOBILES
Kia -> Traction Control System (TCS) Warning Lamp ->
Vehicle: 2009 KIA Borrego EX 4.6 V8 GAS
The TCS warning lamp, will illuminate for 2-4 seconds when the ignition switch is placed in the on position to indicate the warning lamp is operational. The lamp should go off after the 2-4 seconds has elapsed. If the warning lamp remains ...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Borrego MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2009 KIA Borrego AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2009 KIA Borrego EX 4.6 V8 GAS
Lower
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at radiator outlet.
- Remove hose from radiator.
- Reposition hose clamp at thermostat housing.
- Remove hose from thermostat housing.
- Remove hose from vehicle.
- Reverse proc...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Borrego RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2009 KIA Borrego AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2009 KIA Borrego LX 3.8 V6 GAS
- Disconnect battery ground cable.
- Rotate tensioner counterclockwise using suit...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Borrego SERPENTINE BELT SERVICE PROCEDURES
TECHNICAL SERVICE BULLETINS FOR 2009 KIA Borrego AUTOMOBILES
OEM TSB listings for most 2009 KIA Borrego cars and light trucks sold in the U.S. from 1985+.
Document: Torque Specifications on "Torque to Yield" Engine Component Bolts Vehicle: 2009 KIA Borrego LX 3.8 V6 GAS Auto Systems: |
Document: Enhanced Dealer Feedback and Digital Camera Requirements to Support Kia Quality Initiatives Vehicle: 2009 KIA Borrego LX 3.8 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Borrego TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2009 KIA Borrego AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2009 KIA Borrego cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2009 KIA Borrego cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2009 KIA Borrego cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2009 KIA Borrego cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2009 KIA Borrego SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2009 KIA Borrego vehicle. |
Access the Complete guide! |