Auto Parts Search


      Over 40 million used auto parts online. Shop online for auto and truck parts and save up to 75%

Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!
Help me findSearch
Get Full Access Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Toyota Sequoia car and truck repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up & drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your 2008 Toyota Sequoia automobile. Try the Automotix DIY solution today!
DIY REPAIR SAMPLES > CONTINUE EXPLORING >

We have info for following modifications of 2008 Toyota Sequoia

  • 2008 Toyota Sequoia SR5 5.7 V8 GAS, CC:5663, CID:345, Fuel Injection, Aspiration:345
  • 2008 Toyota Sequoia Platinum 5.7 V8 GAS, CC:5663, CID:345, Fuel Injection, Aspiration:345
  • 2008 Toyota Sequoia Limited 5.7 V8 GAS, CC:5663, CID:345, Fuel Injection, Aspiration:345
  • 2008 Toyota Sequoia SR5 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285
  • 2008 Toyota Sequoia Limited 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285

TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES

Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sequoia cars and light trucks sold in the U.S. from mid 1990's+.

Description
Vehicle: 2008 Toyota Sequoia Platinum 5.7 V8 GAS

A tire pressure sensor and transmitter assembly is installed in each tire and wheel assembly. The sensor measures the tire pressure. The measured tire pressure and transmitter identification are transmitted as radio waves to the TPMS (Tire Pressure Monitor System) warning antenna and receiver on the body. From the receiver the signal is sent to the TPMS ECU (Electronic Control Uni...

CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia TIRE PRESSURE MONITORING SYSTEM PROCEDURES

TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES

Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sequoia cars and light trucks sold in the U.S. from mid 1990's+.

Reset Procedures
Vehicle: 2008 Toyota Sequoia Limited 5.7 V8 GAS

This warning lamp will illuminate when tire pressure falls below a specified psi. When the warning lamp illuminates, check the air...

CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia TIRE PRESSURE MONITORING SYSTEM PROCEDURES

TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES

Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sequoia cars and light trucks sold in the U.S. from mid 1990's+.

Diagnosis & Testing -> 2005-06 -> 2007-08 -> Accessing Diagnostic Trouble Codes -> Clearing DTCs (Diagnostic Trouble Codes) -> Diagnostic Trouble Code Identification -> Reset Switch Test -> Using Scan Tool -> Using TPMS Warning Lamp
Vehicle: 2008 Toyota Sequoia Platinum 5.7 V8 GAS

Accessing Diagnostic Trouble Codes

Using TPMS Warning Lamp
  • Place the ignition switch in the Off position.
  • Using Toyota SST or other suitable jumper, connect terminals TC and CG of DLC3. The DLC3 is located under the left side of the instrument panel, Fig. .
  • Place the ignition switch in the On position.
  • Read and note DTCs indicated by flashes of the TPMS warning lamp, Fig. .
  • If the TPMS warning lamp blinks in .25 second intervals, a normal condition is indicated, Fig. .
  • If the TPMS warning lamp blinks in .5 second intervals followed by a 1.5 second pause, then additional .5 second i...

CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia TIRE PRESSURE MONITORING SYSTEM PROCEDURES

TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES

Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sequoia cars and light trucks sold in the U.S. from mid 1990's+.

Reset Procedures
Vehicle: 2008 Toyota Sequoia SR5 5.7 V8 GAS

This warning lamp will illuminate when tire pressure falls below a specified psi. When the warning lamp illuminates, check the air...

CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia TIRE PRESSURE MONITORING SYSTEM PROCEDURES

TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES

Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sequoia cars and light trucks sold in the U.S. from mid 1990's+.

Relearn Procedures -> 2005-06 -> 2007-08 -> Initialization -> Registration -> TPMS Pressure Warning Valve & Transmitter
Vehicle: 2008 Toyota Sequoia SR5 4.7 V8 GAS

Initialization

2005-06
  • Check and adjust tire pressure including spare to manufacturer's specifications.
  • Turn the ignition switch to On position.
  • Press and the hold tire pressure warning reset switch until warning lamp blinks three times at a one second interval.
  • Initialization is completed in about 20 minutes when tire pressure warning ECU has received signals from all wheels including spare.
  • Check that pressure for each tire is displayed in INIT THRESHOLD 1 to 5.
2007-08

Initialize the TPMS using a suitably programmed scan tool.

Registration

If replacing the TPMS ECU, prior to removal...

CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia TIRE PRESSURE MONITORING SYSTEM PROCEDURES

TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES

Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sequoia cars and light trucks sold in the U.S. from mid 1990's+.

Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2008 Toyota Sequoia Limited 5.7 V8 GAS

Refer toFigs. and for wir...

[[table data]]

CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia TIRE PRESSURE MONITORING SYSTEM PROCEDURES

Shop online for auto body parts, engines, wheels, lights...

Click here to view more details about 2004 Toyota Sequoia Tail Light, Passenger Side2004 Toyota Sequoia Tail Light, Passenger Side.

Source: Auto Body Parts Store

$72.24

Click here to view more details about 2011 Toyota Sequoia Antenna2011 Toyota Sequoia Antenna, 4-section mast; 1200 mm cable; With top and side key; A high quality universal fender mount antenna; May require modification or other adjustment to your vehicle upon installation; Backed by 1-year, unlimited-mileage warranty..

Source: Auto Body Parts Store

$5.62

Click here to view more details2012 Toyota Sequoia 18" X 8" Steel Wheel, STEEL WHEEL, 18 X 8, 5 STUDS/LUGS, 150MM BOLT DIA, 18 HOLES, BLACK, UNIVERSAL; STEEL, , .

Source: Wheels / Rims, Mirrors & Lights Store

$64.45

Click here to view more details2010 Toyota Sequoia V8, 5.7 L, 350 CID Rebuilt Engine, Warranty: 3-Year/100,000 Mile, .

Source: Rebuilt Engines Store

Ad Hoc

Click here to view more details2008 Toyota Sequoia Used Engine Computer, Air & Fuel Cont; (eng mtd), R., Very Good.

Source: Used Auto Parts Store

$157.00

Click here to view more details2009 Toyota Sequoia Used Bumper Bar, Front, 52111-OC901W/ SENSOR BAR ONLY (X REINFORCEMENT), Very Good.

Source: Used Auto Parts Store

$330.00
More parts
Help me findSearch
Auto Repair Quick Search
Help me find
Search DIY repair manuals by VIN...
Vehicle Identification Number is a unique serial number used by the automotive industry to identify individual motor vehicles

Find out what info we have for your vehicle

Get the Complete Technical Service Bulletins!
Get the Complete Technical Service Bulletins!Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Toyota Sequoia vehicle.
Access the Complete guide!
Need To Fix Your Car or Truck?
Save Money With Free Car Insurance Quote
FREE car insurance quote
Enter Zip Code:
GOT A WEBSITE?Make money with Automotix

Make money with Automotix Partner Program.

Learn more

Auto Repair Quick Search
Help me find