Auto Parts Search
We have info for following modifications of 2008 Land Rover LR2
- 2008 Land Rover LR2 SE 3.2 L6 GAS, CC:3192, Fuel Injection, Engine VIN:, Desg:N
- 2008 Land Rover LR2 HSE 3.2 L6 GAS, CC:3192, Fuel Injection, Engine VIN:, Desg:N
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Land Rover LR2 AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Land Rover LR2 cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures
Vehicle: 2008 Land Rover LR2 HSE 3.2 L6 GAS
If a new tire pressure sensor is installed on any road wheel, the software can learn the ne...
CLICK HERE TO GET FULL ACCESS TO 2008 Land Rover LR2 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Land Rover LR2 AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Land Rover LR2 cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Identification
Vehicle: 2008 Land Rover LR2 SE 3.2 L6 GAS
Accessing Diagnostic Trouble Codes
Connect a suitable scan tool the DLC (Data Link Connector). The DL is located under the left side of the instrument panel. Follow the scan tool manuf...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Land Rover LR2 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Land Rover LR2 AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Land Rover LR2 cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> Tire Pressure Sensor -> TPMS Front Antenna -> TPMS Rear Antenna
Vehicle: 2008 Land Rover LR2 SE 3.2 L6 GAS
Tire Pressure Sensor
Removal
- Loosen the wheel lug nuts.
- Raise and support the vehicle with jack stands, then remove the wheel and tire assembly.
- Remove the tire valve cap and core and release the air from the tire.
- Separate the bead on the inside and outside of the tire, note the following:
- The bead breaker tool should not be used within 12 inch of the sensor valve in either direction.
- Position the shoe of the tool between 2 to 4 inches away from the sensor valve.
- The lever and tire must not come in contact with the sensor.
- Remove the tire pressure sensor nut, then the sensor, Fig....
CLICK HERE TO GET FULL ACCESS TO 2008 Land Rover LR2 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Land Rover LR2 AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Land Rover LR2 cars and light trucks sold in the U.S. from mid 1990's+.
Component Locations
Vehicle: 2008 Land Rover LR2 SE 3.2 L6 GAS
Refer to F...
CLICK HERE TO GET FULL ACCESS TO 2008 Land Rover LR2 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Land Rover LR2 AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Land Rover LR2 cars and light trucks sold in the U.S. from mid 1990's+.
Component Locations
Vehicle: 2008 Land Rover LR2 HSE 3.2 L6 GAS
Refer to F...
CLICK HERE TO GET FULL ACCESS TO 2008 Land Rover LR2 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Land Rover LR2 AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Land Rover LR2 cars and light trucks sold in the U.S. from mid 1990's+.
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2008 Land Rover LR2 HSE 3.2 L6 GAS
Refer to Fig. for wirin...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Land Rover LR2 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Land Rover LR2 vehicle. |
Access the Complete guide! |