Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2006 Toyota Tacoma car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2006 Toyota Tacoma automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2006 Toyota Tacoma
- 2006 Toyota Tacoma 2.7 L4 GAS, CC:2694, Fuel Injection
- 2006 Toyota Tacoma 4.0 V6 GAS, CC:3956, Fuel Injection
- 2006 Toyota Tacoma X-RUNNER 4.0 V6 GAS, CC:3956, Fuel Injection
- 2006 Toyota Tacoma PRE Runner 2.7 L4 GAS, CC:2694, Fuel Injection
- 2006 Toyota Tacoma PRE Runner 4.0 V6 GAS, CC:3956, Fuel Injection
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Toyota Tacoma AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2006 Toyota Tacoma cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> 2006 -> 2007-08 -> Accessing Diagnostic Trouble Codes -> Clearing DTCs (Diagnostic Trouble Codes) -> Diagnostic Trouble Code Identification -> Reset Switch Test -> Using Scan Tool -> Using TPMS Warning Lamp
Vehicle: 2006 Toyota Tacoma PRE Runner 4.0 V6 GAS
Accessing Diagnostic Trouble Codes
Using TPMS Warning Lamp
- Place the ignition switch in the Off position.
- Using Toyota SST or other suitable jumper, connect terminals TC and CG of DLC3. The DLC3 is located under the left side of the instrument panel, Fig. .
- Place the ignition switch in the On position.
- Read and note DTCs indicated by flashes of the TPMS warning lamp, Fig. .
- If the TPMS warning lamp blinks in .25 second intervals, a normal condition is indicated, Fig. .
- If the TPMS warning lamp blinks in .5 second intervals followed by a 1.5 second pause, then additional .5 second i...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tacoma TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Toyota Tacoma AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2006 Toyota Tacoma cars and light trucks sold in the U.S. from mid 1990's+.
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2006 Toyota Tacoma X-RUNNER 4.0 V6 GAS
Refer to Figs. and for wir...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tacoma TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Toyota Tacoma AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2006 Toyota Tacoma cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> TPMS ECU -> TPMS Pressure Warning Valve & Transmitter -> TPMS Receiver
Vehicle: 2006 Toyota Tacoma PRE Runner 2.7 L4 GAS
TPMS Pressure Warning Valve & Transmitter
If installing a replacement tire pressure warning valve and transmitter, note the identification number for use during registration. Refer to the Registration under the "Relearn Procedures."
Removal
- Loosen the wheel lug nuts.
- Raise and support vehicle with jack stands.
- Remove the wheel and tire assembly.
- Remove the tire valve stem cap, then the valve stem core and allow the tire to deflate, Fig. .
- Remove the nut retaining the tire pressure warning valve and transmitter to the wheel assembly, then drop the transmitter inside the tire.
- Using a...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tacoma TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Toyota Tacoma AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2006 Toyota Tacoma cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> TPMS ECU -> TPMS Pressure Warning Valve & Transmitter -> TPMS Receiver
Vehicle: 2006 Toyota Tacoma X-RUNNER 4.0 V6 GAS
TPMS Pressure Warning Valve & Transmitter
If installing a replacement tire pressure warning valve and transmitter, note the identification number for use during registration. Refer to the Registration under the "Relearn Procedures."
Removal
- Loosen the wheel lug nuts.
- Raise and support vehicle with jack stands.
- Remove the wheel and tire assembly.
- Remove the tire valve stem cap, then the valve stem core and allow the tire to deflate, Fig. .
- Remove the nut retaining the tire pressure warning valve and transmitter to the wheel assembly, then drop the transmitter inside the tire.
- Using a...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tacoma TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Toyota Tacoma AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2006 Toyota Tacoma cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> 2006 -> 2007-08 -> Accessing Diagnostic Trouble Codes -> Clearing DTCs (Diagnostic Trouble Codes) -> Diagnostic Trouble Code Identification -> Reset Switch Test -> Using Scan Tool -> Using TPMS Warning Lamp
Vehicle: 2006 Toyota Tacoma PRE Runner 2.7 L4 GAS
Accessing Diagnostic Trouble Codes
Using TPMS Warning Lamp
- Place the ignition switch in the Off position.
- Using Toyota SST or other suitable jumper, connect terminals TC and CG of DLC3. The DLC3 is located under the left side of the instrument panel, Fig. .
- Place the ignition switch in the On position.
- Read and note DTCs indicated by flashes of the TPMS warning lamp, Fig. .
- If the TPMS warning lamp blinks in .25 second intervals, a normal condition is indicated, Fig. .
- If the TPMS warning lamp blinks in .5 second intervals followed by a 1.5 second pause, then additional .5 second i...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tacoma TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Toyota Tacoma AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2006 Toyota Tacoma cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> TPMS ECU -> TPMS Pressure Warning Valve & Transmitter -> TPMS Receiver
Vehicle: 2006 Toyota Tacoma 2.7 L4 GAS
TPMS Pressure Warning Valve & Transmitter
If installing a replacement tire pressure warning valve and transmitter, note the identification number for use during registration. Refer to the Registration under the "Relearn Procedures."
Removal
- Loosen the wheel lug nuts.
- Raise and support vehicle with jack stands.
- Remove the wheel and tire assembly.
- Remove the tire valve stem cap, then the valve stem core and allow the tire to deflate, Fig. .
- Remove the nut retaining the tire pressure warning valve and transmitter to the wheel assembly, then drop the transmitter inside the tire.
- Using a...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tacoma TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2006 Toyota Tacoma vehicle.
|
| Access the Complete guide! |
