Auto Parts Search
2006 Hummer H3 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Hummer REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
BRAKE SERVICE PROCEDURES FOR 2006 Hummer H3 AUTOMOBILES
Hydraulic Brake Systems -> Component Service -> Assemble -> Bendix Master Cylinder -> Delco Master Cylinder -> Disassemble -> Tracker Master Cylinder -> Wheel Cylinder
Vehicle: 2006 Hummer H3 3.5 L5 GAS
Delco Master Cylinder
When performing the following procedures, refer to Figs. and , noting that the composite reservoir may vary in design.
Disassemble
- Remove master cylinder from vehicle.
- Remove reservoir cover and diaphragm. Discard old brake fluid in reservoir.
- Inspect cover and diaphragm. Replace if cut, cracked or deformed.
- Remove fluid level switch and proportioning valve assembly, if equipped.
- Depress primary piston and remove lock ring.
- Plug primary fluid outlet (outlet nearest to cowl when master cylinder is installed), then apply compressed air into secondary fluid outlet ...
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Hummer H3 AUTOMOBILES
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Two Piece Driveshaft
Vehicle: 2006 Hummer H3 3.5 L5 GAS
Front
- Raise and support vehicle.
- Mark the front U-joint to the pinion yoke on the front differential.
- Mark the relationship of the rear U-joint to the transfer case drive flange.
- Remove the retaining nuts and bolts from the drive flange.
- Remove the clamps and retaining bolts from the front drive axle pinion flange.
- Remove the front propeller shaft from the vehicle.
- Using tape and or a rubber band, wrap the front U-joint bearing caps to ensure the caps do not separate from the U-joint.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft to the pinion flang...
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Hummer H3 AUTOMOBILES
Component Locations
Vehicle: 2006 Hummer H3 3.5 L5 GAS
Refer to F...
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2006 Hummer H3 AUTOMOBILES
Alternator, Replace
Vehicle: 2006 Hummer H3 3.5 L5 GAS
- Disconnect battery ground cable.
- Remove drive belt.
- Raise and support vehicle high enough to access air conditioning compressor through wheelhouse.
- Remove lefthand front wheel.
- Remove lefthand wheelhouse liner.
- Disengage air conditioning compressor electrical connector from bracket.
- Recover air conditioning system.
- Disconnect air conditioning condenser and evaporator lines from compressor.
- Remove air conditioning compressor mounting bolts. Upper mounting bolt will remain with air conditioningcompressor.
- Lower vehicle.
- ...
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Hummer H3 AUTOMOBILES
General Motors Corp./Saturn Trucks -> Change Trans Fluid Indicator ->
Vehicle: 2006 Hummer H3 3.5 L5 GAS
This message will appear on the DIC (Driver Information Center) when it is time to change the transmission fluid....
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2006 Hummer H3 AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2006 Hummer H3 3.5 L5 GAS
Lower
- Drain cooling system into a suitable container.
- Remove air cleaner resonator outlet duct.
- Reposition hose clamp from radiator.
- Remove radiator outlet hose from radiator.
- Reposition hose clamp from engine.
- Remove radiator outlet hose from engine and from vehicle.
- Reverse procedure to install.
Upper
- Drai...
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2006 Hummer H3 AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2006 Hummer H3 3.5 L5 GAS
- Rotate tensioner clockwise with a suitable 3/8 inch breaker bar.
- Remove belt from water pump pul...
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2006 Hummer H3 AUTOMOBILES
Component location diagrams for most 2006 Hummer H3 cars and light trucks sold in the U.S. from 1990+.
Tire Pressure Monitoring System Diagram for 2006 Hummer H3 3.5 L5 GAS Components on diagram: |
Navigation Components Diagram for 2006 Hummer H3 3.5 L5 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2006 Hummer H3 AUTOMOBILES
OEM drawn wiring diagrams for most 2006 Hummer H3 cars and light trucks sold in the U.S.
2006 Hummer H3 3.5 L5 GAS Wiring Diagram Components on diagram: |
2006 Hummer H3 3.5 L5 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2006 Hummer H3 AUTOMOBILES
OEM TSB listings for most 2006 Hummer H3 cars and light trucks sold in the U.S. from 1985+.
Document: Engine Rattle Noise after R And R of the Crankshaft Balancer -Inspect Bolt Torque Vehicle: 2006 Hummer H3 3.5 L5 GAS Symptoms: |
Document: GM of Canada New Vehicle Limited Warranty Tire Program Vehicle: 2006 Hummer H3 3.5 L5 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2006 Hummer H3 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2006 Hummer H3 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2006 Hummer H3 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2006 Hummer H3 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2006 Hummer H3 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2006 Hummer H3 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2006 Hummer H3 vehicle. |
Access the Complete guide! |