Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2006 Chevrolet Equinox car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2006 Chevrolet Equinox automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2006 Chevrolet Equinox
- 2006 Chevrolet Equinox LS 3.4 V6 GAS, CID:207, Fuel Injection, Aspiration:207, Engine VIN:, Desg:F
- 2006 Chevrolet Equinox LT 3.4 V6 GAS, CID:207, Fuel Injection, Aspiration:207, Engine VIN:, Desg:F
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chevrolet Equinox AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chevrolet Equinox cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2006 Chevrolet Equinox LT 3.4 V6 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 2006 Chevrolet Equinox DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chevrolet Equinox AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chevrolet Equinox cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2006 Chevrolet Equinox LS 3.4 V6 GAS
Front
- Raise and support vehicle, then remove tire and wheel assembly.
- Remove engine splash shield, and stabilizer shaft link.
- Disconnect wheel speed sensor electrical connector.
- Insert a suitable drift through brake caliper and remove front wheel driveshaft nut.
- Separate outer tie rod end from steering knuckle. Do not loosen tie rod end jam nut.
- Separate lower ball joint from steering knuckle.
- Attach front hub spindle remover tool No. J 42129, or equivalent, then disengage driveshaft from hub and bearing assembly.
- Disengage driveshaft from transaxle using slide hammer tool No. J ...
CLICK HERE TO GET FULL ACCESS TO 2006 Chevrolet Equinox DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chevrolet Equinox AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chevrolet Equinox cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2006 Chevrolet Equinox LS 3.4 V6 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 2006 Chevrolet Equinox DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chevrolet Equinox AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chevrolet Equinox cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Chevrolet Equinox LT 3.4 V6 GAS
- Place transmission in neutral.
- Raise and support vehicle.
- Index mark relationship of propeller shaft to rear drive module flange.
- Remove bolts securing underbody guard loop.
- Remove underbody guard loop.
- Place a support under propeller shaft at rear drive module.
- Remove bolts securing propeller shaft yoke flange to rear drive module flange.
- Index mark relationship of propeller shaft to power take-off unit (PTU) flange.
- Place a support under propeller shaft at PTU.
- Remove bolts securing propeller shaft to PTU flange.
- Place a su...
CLICK HERE TO GET FULL ACCESS TO 2006 Chevrolet Equinox DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chevrolet Equinox AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chevrolet Equinox cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2006 Chevrolet Equinox LS 3.4 V6 GAS
- Place transmission in neutral.
- Raise and support vehicle.
- Index mark relationship of propeller shaft to rear drive module flange.
- Remove bolts securing underbody guard loop.
- Remove underbody guard loop.
- Place a support under propeller shaft at rear drive module.
- Remove bolts securing propeller shaft yoke flange to rear drive module flange.
- Index mark relationship of propeller shaft to power take-off unit (PTU) flange.
- Place a support under propeller shaft at PTU.
- Remove bolts securing propeller shaft to PTU flange.
- Place a su...
CLICK HERE TO GET FULL ACCESS TO 2006 Chevrolet Equinox DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Chevrolet Equinox AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Chevrolet Equinox cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2006 Chevrolet Equinox LT 3.4 V6 GAS
Front
- Raise and support vehicle, then remove tire and wheel assembly.
- Remove engine splash shield, and stabilizer shaft link.
- Disconnect wheel speed sensor electrical connector.
- Insert a suitable drift through brake caliper and remove front wheel driveshaft nut.
- Separate outer tie rod end from steering knuckle. Do not loosen tie rod end jam nut.
- Separate lower ball joint from steering knuckle.
- Attach front hub spindle remover tool No. J 42129, or equivalent, then disengage driveshaft from hub and bearing assembly.
- Disengage driveshaft from transaxle using slide hammer tool No. J ...
CLICK HERE TO GET FULL ACCESS TO 2006 Chevrolet Equinox DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2006 Chevrolet Equinox vehicle.
|
| Access the Complete guide! |
