2005 Toyota Tundra Driveline, U-Joint & CV Axles Replacement (ONLINE REPAIR MANUALS)

Auto Parts Search


Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!
Help me findSearch
Get Full Access Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2005 Toyota Tundra car and truck repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up & drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your 2005 Toyota Tundra automobile. Try the Automotix DIY solution today!
DIY REPAIR SAMPLES > CONTINUE EXPLORING >

We have info for following modifications of 2005 Toyota Tundra

  • 2005 Toyota Tundra Limited 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285
  • 2005 Toyota Tundra SR5 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285
  • 2005 Toyota Tundra 4.0 V6 GAS, CC:4000, Fuel Injection
  • 2005 Toyota Tundra SR5 4.0 V6 GAS, CC:4000, Fuel Injection
  • 2005 Toyota Tundra 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Toyota Tundra AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Toyota Tundra cars and light trucks from 1990+.

CV AXLE SHAFT, Replace
Vehicle: 2005 Toyota Tundra 4.7 V8 GAS

  • Raise and support vehicle.
  • Remove wheel and tire assembly.
  • Remove engine under-cover.
  • Drain differential oil.
  • Remove drive shaft lock nut grease cap, using a screwdriver and hammer.
  • Remove cotter pin and lock cap from drive shaft lock nut.
  • With an assistant applying brakes, remove drive shaft lock nut.
  • Remove cotter pin and nut from lower ball joint.
  • Disconnect lower suspension arm, using a suitable pry tool.
  • Disconnect drive shaft from hub by pushing steering knuckle outward. Be careful not to damage oil seal, bo...

CLICK HERE TO GET FULL ACCESS TO 2005 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Toyota Tundra AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Toyota Tundra cars and light trucks from 1990+.

DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2005 Toyota Tundra SR5 4.0 V6 GAS

Disassemble

This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.

  • Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance. Do not tighten driveshaft too tightly in a vise because this will cause driveline to become out of balance and result in driveline vibration.
  • Tap outside of bearing cap with a drift to loosen snap ring.
  • Remove snap ri...

CLICK HERE TO GET FULL ACCESS TO 2005 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Toyota Tundra AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Toyota Tundra cars and light trucks from 1990+.

CV AXLE SHAFT, Replace
Vehicle: 2005 Toyota Tundra 4.0 V6 GAS

  • Raise and support vehicle.
  • Remove wheel and tire assembly.
  • Remove engine under-cover.
  • Drain differential oil.
  • Remove drive shaft lock nut grease cap, using a screwdriver and hammer.
  • Remove cotter pin and lock cap from drive shaft lock nut.
  • With an assistant applying brakes, remove drive shaft lock nut.
  • Remove cotter pin and nut from lower ball joint.
  • Disconnect lower suspension arm, using a suitable pry tool.
  • Disconnect drive shaft from hub by pushing steering knuckle outward. Be careful not to damage oil seal, bo...

CLICK HERE TO GET FULL ACCESS TO 2005 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Toyota Tundra AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Toyota Tundra cars and light trucks from 1990+.

DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2005 Toyota Tundra SR5 4.7 V8 GAS

Disassemble

This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.

  • Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance. Do not tighten driveshaft too tightly in a vise because this will cause driveline to become out of balance and result in driveline vibration.
  • Tap outside of bearing cap with a drift to loosen snap ring.
  • Remove snap ri...

CLICK HERE TO GET FULL ACCESS TO 2005 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Toyota Tundra AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Toyota Tundra cars and light trucks from 1990+.

DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2005 Toyota Tundra Limited 4.7 V8 GAS

Disassemble

This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.

  • Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance. Do not tighten driveshaft too tightly in a vise because this will cause driveline to become out of balance and result in driveline vibration.
  • Tap outside of bearing cap with a drift to loosen snap ring.
  • Remove snap ri...

CLICK HERE TO GET FULL ACCESS TO 2005 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Toyota Tundra AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Toyota Tundra cars and light trucks from 1990+.

CV AXLE SHAFT, Replace
Vehicle: 2005 Toyota Tundra SR5 4.7 V8 GAS

  • Raise and support vehicle.
  • Remove wheel and tire assembly.
  • Remove engine under-cover.
  • Drain differential oil.
  • Remove drive shaft lock nut grease cap, using a screwdriver and hammer.
  • Remove cotter pin and lock cap from drive shaft lock nut.
  • With an assistant applying brakes, remove drive shaft lock nut.
  • Remove cotter pin and nut from lower ball joint.
  • Disconnect lower suspension arm, using a suitable pry tool.
  • Disconnect drive shaft from hub by pushing steering knuckle outward. Be careful not to damage oil seal, bo...

CLICK HERE TO GET FULL ACCESS TO 2005 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

Shop online for auto body parts, engines, wheels, lights...

Click here to view more details about 2005 Toyota Tundra Nerf Bars2005 Toyota Tundra Nerf Bars, 3 in. diameter steel tubing; Features UV-resistant molded polymer step pads that will not crack or fade; Superior quality; Vehicle specific design; Easy installation; With Kool Vue's 1-year warranty..

Source: Auto Body Parts Store

$69.33

Click here to view more details about 2002 Toyota Tundra Mirror, Passenger Side2002 Toyota Tundra Mirror, Passenger Side.

Source: Auto Body Parts Store

$127.84

Click here to view more details2015 Toyota Venza 20" x 7.5" Alloy Wheel, Alloy Wheel; 20 X 7.5; 5 Spokes; 5 Lug; 4.5 Inch BP; All Painted Smoked Hypersilver, , .

Source: Wheels / Rims, Mirrors & Lights Store

$261.50

Click here to view more details2010 Toyota Tundra V8, 5.7 L, 350 CID Rebuilt Engine, Warranty: 3-Year/100,000 Mile, .

Source: Rebuilt Engines Store

Ad Hoc

Click here to view more details2008 Toyota Tundra Used Bumper Cover, Front, STEEL BAR ONLY, 2D1, 0S1 MOVE TO FBR, Good.

Source: Used Auto Parts Store

$377.00

Click here to view more details2005 Toyota Tundra Used Upper Control Arm, Passenger Side, 4.7, AUTO, 4X4, Very Good.

Source: Used Auto Parts Store

$86.00
More parts
Help me findSearch
Auto Repair Quick Search
Help me find
Search DIY repair manuals by VIN...
Vehicle Identification Number is a unique serial number used by the automotive industry to identify individual motor vehicles

Find out what info we have for your vehicle

Get the Complete Technical Service Bulletins!
Get the Complete Technical Service Bulletins!Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2005 Toyota Tundra vehicle.
Access the Complete guide!
Need To Fix Your Car or Truck?
Save Money With Free Car Insurance Quote
FREE car insurance quote
Enter Zip Code:
Auto Repair Quick Search
Help me find