Auto Parts Search
We have info for following modifications of 2005 Mazda Tribute
- 2005 Mazda Tribute S 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:1
- 2005 Mazda Tribute I 2.3 L4 GAS, CID:140, Fuel Injection, Aspiration:140, Engine VIN:, Desg:Z
BRAKE SERVICE PROCEDURES FOR 2005 Mazda Tribute AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Mazda Tribute cars and light trucks from 1990+.
Mazda -> Disc Brakes -> Caliper Service -> B-Series -> Front -> Miata & RX-8 -> MPV -> Protege -> Rear -> Replacement -> Service -> Tribute
Vehicle: 2005 Mazda Tribute I 2.3 L4 GAS
Front
B-Series
Replacement
- Raise and support vehicle and remove wheel.
- Remove brake line and plug to avoid fluid loss and air entering line.
- Remove caliper mounting bolts.
- Reverse procedure to install.
Service
- Remove excess dirt from caliper assembly, then remove and discard dust boot.
- Place a piece of wood in caliper and gently blow compressed air into brake line hole to help force out piston. Do not pry piston out, as you may damage assembly.
- Inspect piston for wear and corrosion. Replace as needed.
- Remove piston seal and discard.
- Remove and inspect bleeder screw. Replace as needed.
- Inspec...
CLICK HERE TO GET FULL ACCESS TO 2005 Mazda Tribute BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Mazda Tribute AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Mazda Tribute cars and light trucks from 1990+.
Mazda -> Power Brake Units -> Troubleshooting -> Check Valve -> Function Check -> Load Test
Vehicle: 2005 Mazda Tribute I 2.3 L4 GAS
Function Check
- Stop engine and depress brake pedal a few times to relieve vacuum.
- With pedal depressed, start engine. After starting engine, pedal should move down slightly. If so, unit is functioning.
- After engine has run two minutes, turn it off. Depress pedal with normal force.
- If the first pedal stroke is long and gets shorter with subsequent strokes, the unit is operating. If a problem is found, inspect check valve, vacuum hose and installation. Repair if required and inspect again.
- Start engine and depress pedal with usual force.
- Stop engine with pedal still depressed. Hold peda...
CLICK HERE TO GET FULL ACCESS TO 2005 Mazda Tribute BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Mazda Tribute AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Mazda Tribute cars and light trucks from 1990+.
Mazda -> Power Brake Units -> Power Brake Unit Service -> Replacement
Vehicle: 2005 Mazda Tribute I 2.3 L4 GAS
Replacement
- Remove master cylinder as outlined under .
- Remove clutch pipe holder, if equipped, then disconnect vacuum hose from power brake unit.
- Disconnect pushrod fork from brake pedal and r...
CLICK HERE TO GET FULL ACCESS TO 2005 Mazda Tribute BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Mazda Tribute AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Mazda Tribute cars and light trucks from 1990+.
Mazda -> Hydraulic Brake Systems -> Brake System Bleed -> B-Series -> Except B-Series & Tribute -> Manual -> Pressure -> Tribute
Vehicle: 2005 Mazda Tribute S 3.0 V6 GAS
Except B-Series & Tribute
- Raise and support vehicle with jack stands.
- Fill reservoir with brake fluid, ensure reservoir is at least half full at all times during bleeding procedure.
- After removing bleeder cap, connect one end of transparent vinyl tube to bleeder and place other end in a clean, clear container that is half full with brake fluid.
- One person should depress pedal a few times, then hold the pedal depressed.
- A second person should loosen the bleeder screw and drain fluid, then retighten screw to specifications.
- Repeat steps 4 and 5 until there are no more air bubbles see...
CLICK HERE TO GET FULL ACCESS TO 2005 Mazda Tribute BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Mazda Tribute AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Mazda Tribute cars and light trucks from 1990+.
Mazda -> Power Brake Units -> Power Brake Unit Service -> Replacement
Vehicle: 2005 Mazda Tribute S 3.0 V6 GAS
Replacement
- Remove master cylinder as outlined under .
- Remove clutch pipe holder, if equipped, then disconnect vacuum hose from power brake unit.
- Disconnect pushrod fork from brake pedal and r...
CLICK HERE TO GET FULL ACCESS TO 2005 Mazda Tribute BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 Mazda Tribute AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 Mazda Tribute cars and light trucks from 1990+.
Mazda -> Hydraulic Brake Systems -> Description
Vehicle: 2005 Mazda Tribute I 2.3 L4 GAS
When the brake pedal is depressed, a vacuum builds up in the booster which amplifies the pedal force, pressing on the piston in the master cylinder. The piston raises the hydraulic pressure in the cylinder. This hydraulic pressure i...
CLICK HERE TO GET FULL ACCESS TO 2005 Mazda Tribute BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2005 Mazda Tribute vehicle. |
Access the Complete guide! |