Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2004 Isuzu Ascender car and truck
repair procedures including Isuzu engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2004 Isuzu Ascender automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2004 Isuzu Ascender
- 2004 Isuzu Ascender 4.2 L6 GAS, CID:256, Fuel Injection, Aspiration:256, Engine VIN:, Desg:S
- 2004 Isuzu Ascender 5.3 V8 GAS, CID:323, Fuel Injection, Aspiration:323, Engine VIN:, Desg:P
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2004 Isuzu Ascender AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2004 Isuzu Ascender cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Nylon Injected Rings -> Snap Ring Type
Vehicle: 2004 Isuzu Ascender 5.3 V8 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped wit companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with a...
CLICK HERE TO GET FULL ACCESS TO 2004 Isuzu Ascender DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2004 Isuzu Ascender AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2004 Isuzu Ascender cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2004 Isuzu Ascender 5.3 V8 GAS
Front
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove bolts securing engine shield.
- Remove wheel speed sensor wiring harness from its retainer.
- Disconnect wheel speed sensor from harness.
- Remove retaining bolt for front brake hose.
- Remove front stabilizer bar link from lower control arm.
- Remove upper shock module retaining from shock tower.
- Remove steering knuckle bolts from upper control arm.
- Remove front wheel drive axle from steering knuckle.
- Support front shock steering knuckle to frame.
- Disconnect left s...
CLICK HERE TO GET FULL ACCESS TO 2004 Isuzu Ascender DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2004 Isuzu Ascender AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2004 Isuzu Ascender cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Injected Rings -> Nylon Injected Rings -> Snap Ring Type
Vehicle: 2004 Isuzu Ascender 4.2 L6 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with ...
CLICK HERE TO GET FULL ACCESS TO 2004 Isuzu Ascender DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2004 Isuzu Ascender AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2004 Isuzu Ascender cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Rear
Vehicle: 2004 Isuzu Ascender 5.3 V8 GAS
Rear
- Raise and support vehicle and support it with safety stands in proper locations.
- Mark relationship of components before removal.
- Remove bolts from steering gear crossmember
- Reference mark relationship of driveline to rear axle pinion yoke.
- Reference mark driveline to transmission or transfer case.
- Remove bolts securing yoke retainers from rear axle pinion yoke.
- Slide driveline forward in order to disconnect driveline shaft from rear ax...
CLICK HERE TO GET FULL ACCESS TO 2004 Isuzu Ascender DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2004 Isuzu Ascender AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2004 Isuzu Ascender cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Rear
Vehicle: 2004 Isuzu Ascender 4.2 L6 GAS
Rear
- Raise and support vehicle and support it with safety stands in proper locations.
- Mark relationship of components before removal.
- Remove bolts from steering gear crossmember
- Reference mark relationship of driveline to rear axle pinion yoke.
- Reference mark driveline to transmission or transfer case.
- Remove bolts securing yoke retainers from rear axle pinion yoke.
- Slide driveline forward in order to disconnect driveline shaft from rear ax...
CLICK HERE TO GET FULL ACCESS TO 2004 Isuzu Ascender DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2004 Isuzu Ascender AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2004 Isuzu Ascender cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2004 Isuzu Ascender 4.2 L6 GAS
Front
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove bolts securing engine shield.
- Remove wheel speed sensor wiring harness from its retainer.
- Disconnect wheel speed sensor from harness.
- Remove retaining bolt for front brake hose.
- Remove front stabilizer bar link from lower control arm.
- Remove upper shock module retaining from shock tower.
- Remove steering knuckle bolts from upper control arm.
- Remove front wheel drive axle from steering knuckle.
- Support front shock steering knuckle to frame.
- Disconnect left s...
CLICK HERE TO GET FULL ACCESS TO 2004 Isuzu Ascender DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2004 Isuzu Ascender vehicle.
|
| Access the Complete guide! |
