Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2003 Hyundai Sonata car and truck
repair procedures including Hyundai engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2003 Hyundai Sonata automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2003 Hyundai Sonata
- 2003 Hyundai Sonata 2.4 L4 GAS, CC:2351, Fuel Injection, Engine VIN:, Desg:S
- 2003 Hyundai Sonata 2.7 V6 GAS, CC:2656, Fuel Injection
- 2003 Hyundai Sonata GLS 2.7 V6 GAS, CC:2656, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 2003 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Hyundai Sonata cars and light trucks from 1990+.
Hyundai -> Drum Brakes -> Adjustments -> Parking Brake
Vehicle: 2003 Hyundai Sonata GLS 2.7 V6 GAS
Parking Brake
Service brakes must be properly adjusted before attempting to adjust parking brake lever.
- Pull parking brake lever upward with a force of approximately 44 lbs. noting the following:
- On Accent models, a stroke of 5-7 notches on lever is acceptable.
- ...
CLICK HERE TO GET FULL ACCESS TO 2003 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Hyundai Sonata cars and light trucks from 1990+.
Hyundai -> Disc Brakes -> Brake Pad Service -> Accent -> Elantra & Tiburon -> Elantra, Sonata & Tiburon -> Front -> Rear -> Santa Fe & Tucson -> Sonata -> XG 350
Vehicle: 2003 Hyundai Sonata 2.7 V6 GAS
Front
Accent
- Raise and support vehicle, then remove wheel/tire assembly.
- Remove lower bolt and caliper assembly, Fig. . Position assembly aside using suitable wire.
- Remove brake pads and shim.
- Bottom piston in caliper using a suitable tool.
- Install new brake pads and attach shim to the outer pad. Tighten lower bolt to specifications.
Elantra, Sonata & Tiburon
- Raise and support vehicle, then remove wheel/tire assembly.
- Remove two mounting bolts attaching caliper to torque plate, Fig. .
- Remove brake caliper assembly, then position aside using suitable wire.
- Remove brake pads.
- Install pad cl...
CLICK HERE TO GET FULL ACCESS TO 2003 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Hyundai Sonata cars and light trucks from 1990+.
Hyundai -> Disc Brakes -> Caliper Service -> Accent -> Assemble -> Disassemble -> Elantra & Tiburon -> Elantra, Sonata & Tiburon -> Front -> Installation -> Rear -> Removal -> Santa Fe & Tucson -> Sonata -> XG 350
Vehicle: 2003 Hyundai Sonata 2.7 V6 GAS
Front
Accent
Removal
- Remove wheel/tire assembly.
- Remove brake hose from caliper and cap brake line(s).
- Remove caliper assembly as outlined under .
Disassemble
- Remove sleeve, sleeve boot and pin boots, Fig. .
- Protect fingers with shop towel, then blow piston from caliper bore with compressed air.
- Remove piston boot, then pry piston seal from caliper bore using a suitable screwdriver.
Assemble
- Clean all components with suitable cleaner.
- Inspect caliper bore, piston and carrier for damage or excessive wear.
- Apply suitable rubber grease to new piston seal, then install piston seal in caliper bor...
CLICK HERE TO GET FULL ACCESS TO 2003 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Hyundai Sonata cars and light trucks from 1990+.
Hyundai -> Disc Brakes -> Tightening Specifications
Vehicle: 2003 Hyundai Sonata 2.7 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2003 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Hyundai Sonata cars and light trucks from 1990+.
Hyundai -> Hydraulic Brake Systems -> Component Service -> Master Cylinder Overhaul
Vehicle: 2003 Hyundai Sonata 2.7 V6 GAS
Master Cylinder Overhaul
- Remove reservoir cap, drain brake fluid into a suitable container, then remove reservoir from master cylinder, Figs. through .
- Remove snap ring while depressing piston with a blunt tool. If required, secure master cylinder in a suitable soft jawed vise.
- On all models except Santa Fe, Sonata, Tucson & XG 350 models, remove primary and secondary pistons from master cylinder body. Do not disassemble primary and secondary pistons.
- On Santa Fe...
CLICK HERE TO GET FULL ACCESS TO 2003 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Hyundai Sonata cars and light trucks from 1990+.
Hyundai -> Hydraulic Brake Systems -> Brake System Bleed -> Less Anti-Lock Brakes -> With Anti-Lock Brakes
Vehicle: 2003 Hyundai Sonata 2.7 V6 GAS
Less Anti-Lock Brakes
- Fill master cylinder reservoir with brake fluid.
- Insert end of hose into a container full of brake fluid using a suitable length and diameter of vinyl hose.
- Secure other end of hose to wheel cylinder bleeder plug farthest from master cylinder.
- An assistant should depress brake pedal slowly several times, then hold-down, do not depress completely.
- Loosen bleeder valve, then watch for air bubbles in fluid.
- Tighten bleeder screw before pressure is lost inline. Tighten bleeder screw.
- Repeat procedure until all air bubbles are absent, brake pedal is firm and no leak...
CLICK HERE TO GET FULL ACCESS TO 2003 Hyundai Sonata BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2003 Hyundai Sonata vehicle.
|
| Access the Complete guide! |
