Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 2002 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Pontiac Montana cars and light trucks from 1990+.
Drum Brakes -> Tightening Specifications
Vehicle: 2002 Pontiac Montana 3.4 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2002 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Pontiac Montana cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Tightening Specifications
Vehicle: 2002 Pontiac Montana 3.4 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2002 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Pontiac Montana cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Astro, Bravada, S & T Series & Safari -> Aztek, Rendezvous & Vue -> C & K Series -> Duo-Servo -> Express & Savana -> Installation -> Montana, Silhouette, Trans Sport & Venture -> P Series -> Removal -> Single-Servo -> Tracker
Vehicle: 2002 Pontiac Montana 3.4 V6 GAS
C & K Series
Duo-Servo
Removal
- Raise and support vehicle.
- Mark relationship of wheel to hub, then remove tire and wheel assembly.
- On models equipped with full-floating axles, remove hub and drum assembly as outlined in. "Drive Axles."
- On models equipped with semi-floating axles, proceed as follows:
- Install pin into park brake lever.
- Mark relationship of drum to axle.
- Remove rear brake drum retainers, as required.
- Remove rear brake drum.
- On all models, remove return springs and shoe guide,. Fig. .
- Remove brake hold down springs and pins.
- Disconnect actuator lever and pivot.
- Remove lever return sp...
CLICK HERE TO GET FULL ACCESS TO 2002 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Pontiac Montana cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description -> Hydraulic Control Valves -> Master Cylinder
Vehicle: 2002 Pontiac Montana 3.4 V6 GAS
Master Cylinder
Some vehicles use a conventional tandem master cylinder with two hydraulic pistons operating in-line. The primary piston controls the front brake system and the secondary piston controls the rear brake system.
Other models use a master cylinder that operates the same as the conventional master cylinder, but also incorporates a quick take-up feature in the rear chamber to reduce excessive pedal travel which may result from increased fluid displacement required to move the low drag caliper piston out against the rotor.
The quick take-up uses a spring-loaded ball check val...
CLICK HERE TO GET FULL ACCESS TO 2002 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Pontiac Montana cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Caliper Service -> Assemble -> Disassemble -> Except S & T -> Front -> Inspection -> Installation -> Rear -> Removal -> S & T
Vehicle: 2002 Pontiac Montana 3.4 V6 GAS
Removal
Front
- Siphon brake fluid out of master cylinder until fluid level is approximately 1/3 full, this will prevent fluid overflow when caliper piston is pushed back into its bore.
- Raise and support vehicle, then remove wheels.
- Push piston back into its bore using suitable C-clamp,. Fig. .
- Remove brake caliper hose bolt, then two metal gaskets from brake caliper bolt.
- Remove two caliper mounting bolts and lift caliper off of rotor.
Rear
Except S & T
- Siphon brake fluid out of master cylinder until fluid level is approximately 1/3 full, this will prevent fluid overflow when caliper pist...
CLICK HERE TO GET FULL ACCESS TO 2002 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Pontiac Montana cars and light trucks from 1990+.
Anti-Lock Brakes -> Delphi 7.0 -> System Service -> ABS Automated Bleed -> Brake Pressure Modulator Valve (BPMV) -> Brake System Bleed -> Component Replacement -> Electronic Brake Control Module (EBCM) -> Front Wheel Speed Sensor -> Hydraulic Brake System Bleeding -> Manual -> Pressure -> Rear Wheel Speed Sensor -> Traction Control Switch
Vehicle: 2002 Pontiac Montana 3.4 V6 GAS
Brake System Bleed
ABS Automated Bleed
In most circumstances a base brake bleed is all that is required for most component replacements (such as wheel cylinders, calipers, brake tubes, and master cylinder) except for BPMV replacement.
The following automated ABS bleed procedure is required when one of the following occur: Manual bleeding at the wheel cylinders does not achieve the desired pedal height or feel. Brake Pressure Modulator Valve replacement (BPMV). Extreme loss of brake fluid has occurred. Air ingestion is suspected.
If none of the above conditions apply use standard blee...
CLICK HERE TO GET FULL ACCESS TO 2002 Pontiac Montana BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2002 Pontiac Montana vehicle. |
Access the Complete guide! |