Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2001 Chevrolet Blazer car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2001 Chevrolet Blazer automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2001 Chevrolet Blazer
- 2001 Chevrolet Blazer 4.3 V6 GAS, CID:262, Fuel Injection, Aspiration:262, Engine VIN:, Desg:W
- 2001 Chevrolet Blazer Trailblazer 4.3 V6 GAS, CID:262, Fuel Injection, Aspiration:262, Engine VIN:, Desg:W
BRAKE SERVICE PROCEDURES FOR 2001 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Chevrolet Blazer cars and light trucks from 1990+.
Hydraulic Brake Systems -> Adjustments -> Height Sensing Proportioning Valve
Vehicle: 2001 Chevrolet Blazer 4.3 V6 GAS
Height Sensing Proportioning Valve
The height sensing proportioning valve must be adjusted whenever the valve and/or linkage is disassembled or removed for service. In addition, adjustment should be checked if excessive front wheel lock-up is experienced with a lower than desired brake application rate when vehicle is at or near maximum GVWR.
- Raise and support vehicle, leave wheels on and allow axle to hang freely.
- Remove lever retaining nut and disconnect lever from valve shaft, Fig. .
- Rotate valve shaft to permit installation of correct adjustment gauge, Fig. , ensure D shaped ho...
CLICK HERE TO GET FULL ACCESS TO 2001 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Chevrolet Blazer cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Flush -> Manual Bleed -> Master Cylinder Bleed -> Parking Brake Bleed -> Pressure Bleed
Vehicle: 2001 Chevrolet Blazer Trailblazer 4.3 V6 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in the bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect ...
CLICK HERE TO GET FULL ACCESS TO 2001 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Chevrolet Blazer cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Rotor Replacement -> 2WD Models -> 4WD Models -> Astro, Blazer, Bravada, Jimmy, K1500/2500 & T Series Pickup -> Except Montana, Silhouette, Trans Sport & Venture -> Front -> K3500 -> Montana, Silhouette, Trans Sport & Venture -> Rear
Vehicle: 2001 Chevrolet Blazer Trailblazer 4.3 V6 GAS
2WD Models
Except Montana, Silhouette, Trans Sport & Venture
Front
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove caliper as outlined under "Caliper Service."
- Remove grease cap from hub/rotor, Fig. .
- Remove cotter pin, nut and washer.
- Remove hub/rotor from spindle, being careful not to damage spindle threads or outer bearing.
- Reverse procedure to install, noting the following:
- Apply high-temperature wheel bearing grease to inner and outer wheel bearings.
- Torque nut to 12 ft. lbs. while turning wheel assembly forward by hand, back nut off one flat or until hole in spindle...
CLICK HERE TO GET FULL ACCESS TO 2001 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Chevrolet Blazer cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> Power Brake Unit Service
Vehicle: 2001 Chevrolet Blazer 4.3 V6 GAS
The power brake unit is n...
CLICK HERE TO GET FULL ACCESS TO 2001 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Chevrolet Blazer cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Description
Vehicle: 2001 Chevrolet Blazer Trailblazer 4.3 V6 GAS
The caliper assembly slides on its mounting surfaces, Fig. . Upon brake application, hydraulic pressure against the piston forces the inboard pad against the inboar...
CLICK HERE TO GET FULL ACCESS TO 2001 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Chevrolet Blazer cars and light trucks from 1990+.
Power Brake Units -> Bendix Brake Booster -> Troubleshooting -> Accumulator Leak-Down, System Does Not Hold Charge -> Grabby Brakes Or Booster Chatters/Pedal Vibrates -> Slow Brake Pedal Return
Vehicle: 2001 Chevrolet Blazer 4.3 V6 GAS
Slow Brake Pedal Return
- Excessive seal friction in booster.
- Faulty spool action.
- Restriction in return line from booster to pump reservoir.
- Damaged input rod end.
Grabby Brakes Or Booster Chatters/Pedal Vibrates
- Faulty spool action caused by contamination in sys...
CLICK HERE TO GET FULL ACCESS TO 2001 Chevrolet Blazer BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2001 Chevrolet Blazer vehicle.
|
| Access the Complete guide! |
