Auto Parts Search
We have info for following modifications of 2000 Toyota Tacoma
- 2000 Toyota Tacoma 2.7 L4 GAS, CC:2694, Fuel Injection
- 2000 Toyota Tacoma 3.4 V6 GAS, CC:3378, Fuel Injection
- 2000 Toyota Tacoma 2.4 L4 GAS, CC:2438, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Toyota Tacoma AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Toyota Tacoma cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 2000 Toyota Tacoma 2.4 L4 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance. Do not tighten driveshaft too tightly in a vise because this will cause driveline to become out of balance and result in driveline vibration.
- Tap outside of bearing cap with a drift to loosen snap ring.
- ...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tacoma DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Toyota Tacoma AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Toyota Tacoma cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2000 Toyota Tacoma 2.4 L4 GAS
- Remove front wheel and drive shaft locknut.
- Remove ABS speed sensor and wire harness from steering knuckle.
- Remove bolt, then the brake line clamp from steering knuckle.
- Remove bolts, then the brake caliper and disc. Support brake caliper securely.
- Remove four bolts and disconnect lower ball joint.
- Remove cotter pin, then lo...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tacoma DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Toyota Tacoma AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Toyota Tacoma cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2000 Toyota Tacoma 2.7 L4 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove two center support bearing bolts. While removing set bolts, support center support bearing by hand so that the transmission and intermediate shaft and propeller shaft remain straight line.
- Place reference mark on driveline and differential companion flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolts from differential flange. Bolts inserted in d...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tacoma DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Toyota Tacoma AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Toyota Tacoma cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2000 Toyota Tacoma 3.4 V6 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove two center support bearing bolts. While removing set bolts, support center support bearing by hand so that the transmission and intermediate shaft and propeller shaft remain straight line.
- Place reference mark on driveline and differential companion flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolts from differential flange. Bolts inserted in d...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tacoma DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Toyota Tacoma AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Toyota Tacoma cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2000 Toyota Tacoma 2.7 L4 GAS
- Remove front wheel lug nuts.
- Remove shock absorber.
- Remove wheel hub cap, cotter pin, and locknut.
- While applying brakes, remove locknut.
- Remove wheel hub.
- Remove snap ring using suitable tool.
- Remove spacer.
- On models equipped with ABS, remove ABS speed sensor and wire harness from steering knuckle.
- Remove four bolts and disconnect lower ball joint.
- Remove bolt, then the brake line clamp from steering knuckle.
- Remove bolts,...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tacoma DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2000 Toyota Tacoma AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2000 Toyota Tacoma cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2000 Toyota Tacoma 2.4 L4 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove two center support bearing bolts. While removing set bolts, support center support bearing by hand so that the transmission and intermediate shaft and propeller shaft remain straight line.
- Place reference mark on driveline and differential companion flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolts from differential flange. Bolts inserted in d...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tacoma DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2000 Toyota Tacoma vehicle. |
Access the Complete guide! |