Auto Parts Search
We have info for following modifications of 2000 Mazda Protege
- 2000 Mazda Protege 1.6 L4 GAS, CC:1589, Fuel Injection, Engine VIN:, Desg:0
- 2000 Mazda Protege 1.8 L4 GAS, CC:1839, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 2000 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mazda Protege cars and light trucks from 1990+.
Disc Brakes -> Adjustments -> Lever -> Parking Brake
Vehicle: 2000 Mazda Protege 1.6 L4 GAS
Parking Brake
Lever
- Before adjustment, start engine and depress brake pedal several times.
- Stop engine and remove parking brake lever cover.
- Turn adjusting nut at front of pa...
CLICK HERE TO GET FULL ACCESS TO 2000 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mazda Protege cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> B-Series -> Except B-Series & Tribute -> Manual -> Pressure -> Tribute
Vehicle: 2000 Mazda Protege 1.8 L4 GAS
Except B-Series & Tribute
- Raise and support vehicle with jack stands.
- Fill reservoir with brake fluid, ensure reservoir is at least half full at all times during bleeding procedure.
- After removing bleeder cap, connect one end of transparent vinyl tube to bleeder and place other end in a clean, clear container that is half full with brake fluid.
- One person should depress pedal a few times, then hold the pedal depressed.
- A second person should loosen the bleeder screw and drain fluid, then retighten screw to specifications.
- Repeat steps 4 and 5 until there are no more air bubbles see...
CLICK HERE TO GET FULL ACCESS TO 2000 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mazda Protege cars and light trucks from 1990+.
Anti-lock Brakes -> Component Testing -> 1997 -> 1998-2001 -> 1999-2001 -> ABS Control Module -> ABS Control Unit -> ABS Hydraulic Unit -> ABS Motor -> ABS Motor & Harness -> ABS Motor & Harness To ABS Control Module -> ABS Relay -> ABS Warning Light -> B-Series -> Clearance Inspection -> Control Unit -> Fail-Safe Relay -> Hydraulic System -> Hydraulic Unit -> Miata -> Millenia & Protege -> Motor Relay -> MPV -> MX-6 & 626 -> Pressure Differential Switch -> Rear Axle Speed Sensor -> Rotor Inspection -> Solenoid Valve -> Solenoid Valve & Valve Relay -> Valve Relay -> Voltage Inspection -> Wheel Speed Sensor
Vehicle: 2000 Mazda Protege 1.8 L4 GAS
B-Series
ABS Control Module
1999-2001
Refer to Figs. through , for component testing procedures.
ABS Warning Light
If warning light is inoperative at all times, proceed as follows:
- Inspect warning light bulb; replace as required.
- Inspect No. 10 15A fuse; replace as required.
Hydraulic Unit
1997
Disconnect hydraulic unit connector and measure resistance between terminals 1 and 3 at unit. Resistance should be 18-26 K ohms. If not, replace hydraulic unit.
Rear Axle Speed Sensor
1997
- Raise and support vehicle.
- Remove differential cover and measure clearance between rear axle speed sensor and s...
CLICK HERE TO GET FULL ACCESS TO 2000 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mazda Protege cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 2000 Mazda Protege 1.8 L4 GAS
When the brake pedal is depressed, a vacuum builds up in the booster which amplifies the pedal force, pressing on the piston in the master cylinder. The piston raises the hydraulic pressure in the cylinder. This hydraulic pres...
CLICK HERE TO GET FULL ACCESS TO 2000 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mazda Protege cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> B-Series -> Except B-Series -> Master Cylinder Overhaul -> Wheel Cylinder Overhaul
Vehicle: 2000 Mazda Protege 1.8 L4 GAS
Master Cylinder Overhaul
Except B-Series
- Remove brake fluid from reservoir after removal of master cylinder.
- Refer to Figs. through , for master cylinder disassembly.
- Visually inspect all components and repair or replace any faulty components.
- Reverse procedure to assemble.
B-Series
- Clean outside of master cylinder and drain fluid after removal.
- Remove snap ring by depressing rear piston, Fig. .
- Remove primary piston from master cylinder, then remove secondary piston by directing compressed air ...
CLICK HERE TO GET FULL ACCESS TO 2000 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mazda Protege cars and light trucks from 1990+.
Hydraulic Brake Systems -> Troubleshooting
Vehicle: 2000 Mazda Protege 1.8 L4 GAS
Refer to Fig. , for assistanc...
CLICK HERE TO GET FULL ACCESS TO 2000 Mazda Protege BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2000 Mazda Protege vehicle. |
Access the Complete guide! |