Auto Parts Search
We have info for following modifications of 1999 Isuzu Rodeo
- 1999 Isuzu Rodeo 3.2 V6 GAS, CC:3165, Fuel Injection
- 1999 Isuzu Rodeo 2.2 L4 GAS, CC:2180, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1999 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1999 Isuzu Rodeo cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 1999 Isuzu Rodeo 3.2 V6 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped wit companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with a...
CLICK HERE TO GET FULL ACCESS TO 1999 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1999 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1999 Isuzu Rodeo cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front
Vehicle: 1999 Isuzu Rodeo 2.2 L4 GAS
Front
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Detach outer retainer of center support bearing and remove center support bearing with suitable tool.
- Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolts, nuts, and washers from...
CLICK HERE TO GET FULL ACCESS TO 1999 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1999 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1999 Isuzu Rodeo cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 1999 Isuzu Rodeo 3.2 V6 GAS
Front
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove drain plug from differential and drain in suitable container.
- Remove brake caliper bolt and support caliper with mechanics wire.
- On models equipped with ABS sensor, remove bolt securing anti-lock brake speed sensor.
- Remove hub assembly.
- Remove steering link and arm assembly.
- Remove driveline.
- Remove driveline protector.
- Remove breather hose clips from front driveaxle and disconnect hous...
CLICK HERE TO GET FULL ACCESS TO 1999 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1999 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1999 Isuzu Rodeo cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 1999 Isuzu Rodeo 2.2 L4 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped wit companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with a...
CLICK HERE TO GET FULL ACCESS TO 1999 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1999 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1999 Isuzu Rodeo cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1999 Isuzu Rodeo 3.2 V6 GAS
Front
- Place shift lever in neutral.
- Raise vehicle off ground and support it with safety stands in proper locations.
- Mark flange on front drive. Its recommended to use paint for reference marks. Never damage driveshaft flange and companion flange on front drive.
- Remove exhaust and transfer protectors.
- Remove bolts and then remove driveline from front final drive and transfer case.
- Reverse procedure to install noting the following:
- Torque wheel lug nuts to 85 ft. lbs.
- Torque driveline to transfer companion flange mounting bolts to 46 ft. lbs.
Rear
- Place vehicle in neutral.
- Release parkin...
CLICK HERE TO GET FULL ACCESS TO 1999 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1999 Isuzu Rodeo vehicle. |
Access the Complete guide! |