Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Venture cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Bendix Master Cylinder -> Delco Master Cylinder -> Disassemble -> Tracker Master Cylinder -> Wheel Cylinder
Vehicle: 1998 Chevrolet Venture 3.4 V6 GAS
Delco Master Cylinder
When performing the following procedures, refer to Figs. and noting that the composite reservoir may vary in design.
Disassemble
- Remove master cylinder from vehicle.
- Remove reservoir cover and diaphragm. Discard old brake fluid in reservoir.
- Inspect cover and diaphragm. Replace if cut, cracked or deformed.
- Remove fluid level switch and proportioning valve assembly, if equipped.
- Depress primary piston and remove lock ring.
- Plug primary fluid outlet (outlet nearest to cowl when master cylinder is installed), then apply compressed air into secondary fluid outlet t...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Venture cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Flush -> Manual Bleed -> Master Cylinder Bleed -> Parking Brake Bleed -> Pressure Bleed
Vehicle: 1998 Chevrolet Venture 3.4 V6 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in the bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect ...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Venture cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> Troubleshooting -> Brakes Grab -> Hard Pedal -> Slow Or No Release
Vehicle: 1998 Chevrolet Venture 3.4 V6 GAS
Hard Pedal
- Internal vacuum leak.
- Faulty control valve.
- Broken or damaged hydraulic brake lines.
- Collapsed or damaged vacuum hose.
- Plugged or loose vacuum fitting.
- Bad stud welds on front or rear housing on power head.
- Faulty booster diaphragm.
- Restricted air filter element.
- Worn or distorted reaction plate or levers.
- Cracked or broken pow...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Venture cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Caliper Service -> Assemble -> Blazer, Bravada & Jimmy -> Disassemble -> Front -> Inspection -> Installation -> Rear -> Removal -> Sierra & Silverado
Vehicle: 1998 Chevrolet Venture 3.4 V6 GAS
Removal
Front
- Siphon brake fluid out of master cylinder until fluid level is approximately 1/3 full, this will prevent fluid overflow when caliper piston is pushed back into its bore.
- Raise and support vehicle, then remove wheels.
- Push piston back into its bore using suitable C-clamp, Fig. .
- Remove two caliper mounting bolts and lift caliper off of rotor.
Rear
Blazer, Bravada & Jimmy
- Raise and support vehicle.
- Mark position of wheel to hub for installation reference.
- Remove wheel assembly.
- Remove mounting bolt and disconnect brake hose fitting from caliper. Discard gaskets and plug brake h...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Venture cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Precautions -> Brake Disc Service -> Brake Lines & Linings -> Brake Roughness -> General
Vehicle: 1998 Chevrolet Venture 3.4 V6 GAS
Brake Lines & Linings
Remove one of the front wheels and inspect the brake disc, caliper and linings.
Do not allow any oil or grease on the linings. It is recommended that linings be replaced in sets when worn or damaged.
If the caliper is cracked or fluid leakage through the casting is evident, it must be replaced as a unit.
Brake Roughness
The most common cause of brake chatter on disc brakes is a variation in thickness of the disc. If roughness or vibration is encountered during highway operation or if pedal pumping is experienced at low speeds, the disc may have excessive thickness v...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Venture BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Venture AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Venture cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Astro, Bravada, S & T Series & Safari -> Aztek -> C & K Series -> Duo-Servo -> G Series -> Installation -> Montana, Silhouette, Trans Sport & Venture -> P Series -> Removal -> Single-Servo -> Tracker
Vehicle: 1998 Chevrolet Venture 3.4 V6 GAS
C & K Series
Duo-Servo
Removal
- Raise and support vehicle.
- Mark relationship of wheel to hub, then remove tire and wheel assembly.
- On models equipped with full-floating axles, remove hub and drum assembly as described in "Drive Axles."
- On models equipped with semi-floating axles, proceed as follows:
- Install pin into park brake lever.
- Mark relationship of drum to axle.
- Remove rear brake drum retainers, as required.
- Remove rear brake drum.
- On all models, remove return springs and shoe guide, Fig. .
- Remove brake hold down springs and pins.
- Disconnect actuator lever and pivot.
- Remove lever return spri...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Venture BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1998 Chevrolet Venture vehicle. |
Access the Complete guide! |