Auto Parts Search
We have info for following modifications of 1997 Ford Ranger
- 1997 Ford Ranger 2.3 L4 GAS, CID:140, Fuel Injection, Aspiration:140, Engine VIN:, Desg:A
- 1997 Ford Ranger 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:U
- 1997 Ford Ranger 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:X
- 1997 Ford Ranger Super 2.3 L4 GAS, CID:140, Fuel Injection, Aspiration:140, Engine VIN:, Desg:A
- 1997 Ford Ranger Super 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:U
- 1997 Ford Ranger Super 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:X
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Ford Ranger cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 1997 Ford Ranger 3.0 V6 GAS
Front
- With vehicle in NEUTRAL, position it on a hoist.
- Remove front wheel and tire assembly.
- Remove and discard the hub nut and washer assembly.
- Remove front disc brake caliper, anchor plate and pads as an assembly, and position assembly aside.
- Remove brake disc.
- Separate outboard front wheel halfshaft joint from wheel hub.
- Support front suspension lower arm.
- Remove nut and bolt retaining upper ball joint to front wheel knuckle.
- Remove outboard front wheel halfshaft joint from wheel hub.
- Rotate front wheel knuckle.
- Compress outboard front whe...
CLICK HERE TO GET FULL ACCESS TO 1997 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Ford Ranger cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 1997 Ford Ranger Super 3.0 V6 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 1997 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Ford Ranger cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 1997 Ford Ranger 2.3 L4 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 1997 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Ford Ranger cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 1997 Ford Ranger Super 4.0 V6 GAS
Front
- With vehicle in NEUTRAL, position it on a hoist.
- Remove front wheel and tire assembly.
- Remove and discard the hub nut and washer assembly.
- Remove front disc brake caliper, anchor plate and pads as an assembly, and position assembly aside.
- Remove brake disc.
- Separate outboard front wheel halfshaft joint from wheel hub.
- Support front suspension lower arm.
- Remove nut and bolt retaining upper ball joint to front wheel knuckle.
- Remove outboard front wheel halfshaft joint from wheel hub.
- Rotate front wheel knuckle.
- Compress outboard front whe...
CLICK HERE TO GET FULL ACCESS TO 1997 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Ford Ranger cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 1997 Ford Ranger Super 4.0 V6 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 1997 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Ford Ranger cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 1997 Ford Ranger 4.0 V6 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 1997 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1997 Ford Ranger vehicle. |
Access the Complete guide! |