Auto Parts Search
We have info for following modifications of 1995 Pontiac Trans Sport
- 1995 Pontiac Trans Sport 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:L
- 1995 Pontiac Trans Sport 3.1 V6 GAS, CID:189, Fuel Injection, Aspiration:189, Engine VIN:, Desg:D
BRAKE SERVICE PROCEDURES FOR 1995 Pontiac Trans Sport AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Pontiac Trans Sport cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description -> Hydraulic Control Valves -> Master Cylinder
Vehicle: 1995 Pontiac Trans Sport 3.8 V6 GAS
Master Cylinder
Some vehicles use a conventional tandem master cylinder with two hydraulic pistons operating inline. The primary piston controls the front brake system and the secondary piston controls the rear brake system.
Other models use a master cylinder that operates the same as the conventional master cylinder, but also incorporates a quick take-up feature in the rear chamber to reduce excessive pedal travel which may result from increased fluid displacement required to move the low drag caliper piston out against the rotor.
The quick take-up uses a spring-loaded ball check valv...
CLICK HERE TO GET FULL ACCESS TO 1995 Pontiac Trans Sport BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Pontiac Trans Sport AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Pontiac Trans Sport cars and light trucks from 1990+.
Anti-lock Brakes -> Rear Wheel Anti-Lock Brake System -> System Service -> 1992 -> 1993-95 -> Anti-Lock Pressure Valve (APV) -> Brake System Bleed -> C & K Series -> Component Replacement -> Electronic Brake Control Module (EBCM) -> Electronic Control Unit (ECU) -> Isolation/Dump Valve Assembly -> Manual Bleeding -> Pressure Bleeding -> Vehicle Control Module (VCM) -> Vehicle Speed Sensor
Vehicle: 1995 Pontiac Trans Sport 3.1 V6 GAS
Brake System Bleed
1992
Before bleeding the brakes, the front and rear displacement cylinder pistons must be returned to the top most position. Using a TECH 1 or equivalent scan tool, enter manual control function and apply the front and rear motors. Ensure enable relay is on.
Use only DOT 3 brake fluid from a clean and sealed container. Do not use DOT 5 brake fluid.
Pressure Bleeding
- Remove master cylinder cover, ensure reservoir is properly filled.
- Connect bleeder adapter tool No. J 35589, or equivalent, to master cylinder reservoir.
- Connect bleeder adapter to pressure bleeding equipm...
CLICK HERE TO GET FULL ACCESS TO 1995 Pontiac Trans Sport BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Pontiac Trans Sport AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Pontiac Trans Sport cars and light trucks from 1990+.
Anti-lock Brakes -> Rear Wheel Anti-Lock Brake System -> Troubleshooting
Vehicle: 1995 Pontiac Trans Sport 3.1 V6 GAS
When troubleshooting the anti-lock brake system, refer to "Wiring Diagrams" in "Vehicle Systems" and connectors, Figs. through ; these may be helpful in completing a visual inspection of all relat...
CLICK HERE TO GET FULL ACCESS TO 1995 Pontiac Trans Sport BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Pontiac Trans Sport AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Pontiac Trans Sport cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> C & K Series w/Non-Servo Brakes -> Duo-Servo Brakes -> Installation -> Lumina APV, Silhouette & Trans Sport -> Removal -> Tracker
Vehicle: 1995 Pontiac Trans Sport 3.1 V6 GAS
Duo-Servo Brakes
Removal
- Raise and support vehicle, then remove tire and wheel assembly.
- Remove brake drum. If brake lining is dragging on brake drum, back off brake adjustment by rotating adjustment screw. Refer to individual truck chapter for procedure. If brake drum is rusted or corroded to axle flange and cannot be removed, lightly tap flange to drum mounting surface with a suitable hammer.
- Using brake spring pliers or equivalent, unhook primary and secondary return springs, Fig. . Observe location of brake parts being removed to aid during installation.
- Remove brake hold-down spri...
CLICK HERE TO GET FULL ACCESS TO 1995 Pontiac Trans Sport BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Pontiac Trans Sport AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Pontiac Trans Sport cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Bendix Master Cylinder -> Cast Iron Type -> Composite Type -> Delco-Moraine Master Cylinder -> Disassemble -> Inspection -> Tracker Master Cylinder -> Wheel Cylinder
Vehicle: 1995 Pontiac Trans Sport 3.8 V6 GAS
Delco-Moraine Master Cylinder
Composite Type
When performing the following procedures, refer to Fig. for all models except Lumina APV, Silhouette & Trans Sport, noting that the composite reservoir may vary in design. Refer to Fig. for Lumina APV, Silhouette & Trans Sport models.
Disassemble
- Remove master cylinder from vehicle.
- Remove reservoir cover and diaphragm. Discard old brake fluid in reservoir.
- Inspect cover and diaphragm. Replace if cut, cracked or deformed.
- Remove fluid level switch and proportioning valve assembly, if equipped.
- Depress primary piston and remove lock ring.
- P...
CLICK HERE TO GET FULL ACCESS TO 1995 Pontiac Trans Sport BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Pontiac Trans Sport AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Pontiac Trans Sport cars and light trucks from 1990+.
Hydraulic Brake Systems -> Adjustments -> Height Sensing Proportioning Valve
Vehicle: 1995 Pontiac Trans Sport 3.1 V6 GAS
Height Sensing Proportioning Valve
The height sensing proportioning valve must be adjusted whenever the valve and/or linkage is disassembled or removed for service. In addition, adjustment should be checked if excessive front wheel lock-up is experienced with a lower than desired brake application rate when vehicle is at or near maximum GVWR.
- Raise and support vehicle leaving wheels on, and allow axle to hang freely.
- Remove lever retaining nut and disconnect lever from valve shaft, Fig. .
- Rotate valve shaft to permit installation of correct adjustment gauge, Fig. , ensuring that D shape...
CLICK HERE TO GET FULL ACCESS TO 1995 Pontiac Trans Sport BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1995 Pontiac Trans Sport vehicle. |
Access the Complete guide! |