Auto Parts Search
1995 Chevrolet S10 Pickup CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Chevrolet REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
General Service Domestic Vehicles -> 1994-95 -> Pressure Gauge Indication
Vehicle: 1995 Chevrolet S10 Pickup 4.3 V6 GAS
Due to the different types of models and systems the following typical pressure gauge indications should be used as a guide only, Fig. . Refer to the "Performance Tests" or "System Pressure Check" for the particular model being tested....
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
Disc Brakes -> Delco-Moraine Single Piston Caliper -> Brake Pad Service -> Installation -> Removal
Vehicle: 1995 Chevrolet S10 Pickup 4.3 V6 GAS
Removal
- Remove caliper assembly as outlined above.
- Remove inboard pad with retainer spring. Dislodge outboard pad and position caliper on the front suspension so the brake hose will not support the weight of the caliper.
- Remove two sleeves from inboard ears of the caliper.
- Remove four rubber bushings from the grooves in each of the caliper ears.
Installation
- Lubricate new sleeves, rubber bushings, bushing grooves and mounting bolt ends with Delco Silicone Lube or equivalent.
- Install new bushings and sleeves in caliper ears. Position the sleeve so that the end toward the pad is flush ...
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
General Motors Corp./Saturn Light Trucks, SUVs & Vans -> Fuel Filter Replacement -> Gasoline Engines Except Equinox, Montana SV6, Relay, Rendezvous w/3.6L Engine, Terraza, Uplander & Vue (2004-06) & 2004-06 Envoy, Rainier & TrailBlazer -> Returnless Fuel System
Vehicle: 1995 Chevrolet S10 Pickup 2.2 L4 GAS
Returnless Fuel System
On models equipped with fuel injected engines, relieve fuel system pressure as outlined under "Fuel System Pressure Relief."
On models equipped with metal collar quick disconnect connectors, GM tool No. J37088-A, or equivalent, will be required to disconnect the connector. Pri...
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1995 Chevrolet S10 Pickup 4.3 V6 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
Alternator, Replace
Vehicle: 1995 Chevrolet S10 Pickup 4.3 V6 GAS
- Disconnect battery ground cable.
- Remove alternator drive belt.
- Remove alternator mounting bolts.
- Remove output terminal nut.
- Disconnect electrical connector.
- Remove alternator from vehicle.
- Reverse procedure to install, noting t...
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
General Motors Corp./Saturn Trucks -> Check Engine/Service Engine Soon Indicator Lamp -> Electronic Engine Controls Or Electronic Fuel Injection Except Tracker
Vehicle: 1995 Chevrolet S10 Pickup 4.3 V6 GAS
The Check Engine/Service Engine Soon Lamp should light when the ignition is turned On. When the engine is started, the lamp should go off. If the lamp remains on for 10 seconds or constantly after the engine is started, the self diagnosis system has detected a problem and has stored a code in the system Electronic Control Module (ECM) or Powertrain Control Module (PCM). After diagnosis and repair, the ECM/PCM memory can be cleared of codes either by using a scan tool (OBD II systems) or by disconnecting the battery ground ca...
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 1995 Chevrolet S10 Pickup 4.3 V6 GAS
Inlet
- Remove air cleaner.
- Drain cooling system into a suitable container.
- Remove heater hose support clamp bolt.
- Reposition heater core inlet hose clamp at engine.
- Remove hose from engine.
- Reposition heater hose inlet clamp at heater core.
- Remove heater inlet hose from heater core.
- Remove hose from vehicle.
- Reverse procedure to in...
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1995 Chevrolet S10 Pickup 2.2 L4 GAS
- Disconnect battery ground cable.
- Pivot tensioner, using 19mm wrench.
- Remove belt from alt...
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
Component location diagrams for most 1995 Chevrolet S10 Pickup cars and light trucks sold in the U.S. from 1990+.
Junction Block Diagram for 1995 Chevrolet S10 Pickup 4.3 V6 GAS Components on diagram: |
LH Side Of I/P Diagram for 1995 Chevrolet S10 Pickup 4.3 V6 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
OEM drawn wiring diagrams for most 1995 Chevrolet S10 Pickup cars and light trucks sold in the U.S.
1995 Chevrolet S10 Pickup 2.2 L4 GAS Wiring Diagram Components on diagram: |
1995 Chevrolet S10 Pickup 2.2 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
OEM TSB listings for most 1995 Chevrolet S10 Pickup cars and light trucks sold in the U.S. from 1985+.
Document: New Website for AFIT, TPM, and VDR Updates Vehicle: 1995 Chevrolet S10 Pickup 2.2 L4 GAS Auto Systems: |
Document: Car and Truck Fix It Right the First Time Issues Vehicle: 1995 Chevrolet S10 Pickup 2.2 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1995 Chevrolet S10 Pickup AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1995 Chevrolet S10 Pickup cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1995 Chevrolet S10 Pickup cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1995 Chevrolet S10 Pickup cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1995 Chevrolet S10 Pickup cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1995 Chevrolet S10 Pickup SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1995 Chevrolet S10 Pickup vehicle. |
Access the Complete guide! |