Auto Parts Search
1995 BMW 740I CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT BMW REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1995 BMW 740I AUTOMOBILES
Imported Cars & Light Trucks & Vans -> 1993-95 -> Leak Test -> Electronic Leak Detectors -> Flame-Type (Halide) Leak Detectors -> Fluid Leak Detectors
Vehicle: 1995 BMW 740I 4.0 V8 GAS
Testing the refrigerant system for leaks is one of the most important phases of troubleshooting. One or more of the methods outlined will prove useful in detecting leaks or checking connections if service work is performed. Before beginning any leak test, attach a manifold gauge set and note pressure. If little or no pressure is indicated, a partial charge must be installed. Check all connections, compressor head gasket, oil filler plug and compressor shaft seal for leaks.
R-12 leak detectors will not detect R-134a leaks. For R-134a system an electronic type leak detector i...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 BMW 740I AUTOMOBILES
Power Brake Units -> Diagnosis & Testing -> Brake Booster Vacuum Supply Check -> Function Test -> Hydraulic Booster Supply
Vehicle: 1995 BMW 740I 4.0 V8 GAS
Function Test
- Operate brake pedal 10 times with engine stopped.
- If brake pedal gives, system is okay.
- On models equipped with vacuum booster systems,if brake pedal does not give, check valve, vacuum hose and/or rubber ring between master cylinder and brake booster could be faulty.
- On models equipped with hydraulic booster systems, check for faulty power steering pump, lines, accumulator and hydr...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1995 BMW 740I AUTOMOBILES
BMW -> Fuel Filter Replacement -> Except X3 & Z4 -> Fuel System Pressure Relief -> Models w/Fitting Or Union Bolt Connection -> Models w/Fuel Hose Connection -> Removal & Installation
Vehicle: 1995 BMW 740I 4.0 V8 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
After the battery has been disconnected and reconnected, some abnormal driveability symptoms may occur. The vehicle may need to be driven while it relearns its adaptive strategy.
Fuel System Pressure Relief
- Obtain the vehicle owner's radio theft protection code.
- Remove the fuel pump relay(s).
- Start the engine and allow it to stall.
- Crank engine for 10 seconds to ensure the fuel pressure has been...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1995 BMW 740I AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 1995 BMW 740I 4.0 V8 GAS
- Raise and support vehicle.
- Remove complete exhaust system.
- Remove heat shield.
- Unfasten screws.
- Unscrew nuts.
- Push constant-velocity joint along disassembly grooves and of output flange.
- Unscrew center bearing.
- Bend propeller shaft downwards on center bearing. Caution: Do not let propeller shaft fall into joints. Join...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1995 BMW 740I AUTOMOBILES
Alternator, Replace -> Air Cooled -> Liquid Cooled
Vehicle: 1995 BMW 740I 4.0 V8 GAS
Air Cooled
- Switch off ignition.
- Disconnect and cover battery ground lead.
- Remove alternator drive belt.
- Remove bolts on oil-filter housing.
- Place oil-filter housing to one side.
- Disconnect plug on alternator.
- Remove nut on alternator B+ terminal.
- Unfasten cable clip.
- Unclip cooling air guide.
- Remove alternator mounting bolts.
- Pull out alternator towards front.
- Pull alternator upwards to remove.
- Remove alternator from vehicle.
- Reverse procedure to install, noting the following:
- Torque alternator B+ terminal nut to 72 to 108 inch lbs.
- Torque alternator mounting bolts to 15 ft. lbs.
Liquid Cool...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 1995 BMW 740I AUTOMOBILES
Cabin Air Filter Service -> BMW -> 1993-2001 7 Series
Vehicle: 1995 BMW 740I 4.0 V8 GAS
Service interval is determined by the service indicator.
- Remove cabin air filter cover retaining screw, then open the cover.
- Depress the cabin air filter duct lock, then lift the cover upward.
- Release the cabin ai...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1995 BMW 740I AUTOMOBILES
BMW -> Service Interval Indicator -> 7 Series -> Interval Indicator -> Less Underhood Diagnostic Connector -> Oil Service -> With Underhood Diagnostic Connector
Vehicle: 1995 BMW 740I 4.0 V8 GAS
Less Underhood Diagnostic Connector
- Press and hold the reset button located at the top lefthand side of the instrument cluster for 10 seconds.
- A four line menu should appear on the speedometer display. First line is the Back function followed by three service and maintenance items.
- A "!" symbol indicates the service or maintenance item can be reset. An "0" symbol indicates the item cannot be reset. The first 20% of the service or maintenance interval is protected against accidental or premature reset.
- Use the Reset button or lower axial FAS button on the turn signal high beam switch to scr...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1995 BMW 740I AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 1995 BMW 740I 4.0 V8 GAS
Inlet
- Drain coolant into a suitable container.
- Reposition hose clamp at heater core and remove hose.
- Reposition hose clamp at heater valve and remove hose.
- Remove hose from vehicle.
- Reverse procedure to install.
Outl...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1995 BMW 740I AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1995 BMW 740I 4.0 V8 GAS
- Remove fan cowl by lifting out expansion rivets on both sides.
- Secure fan pulley with suitable securing tool, or equivalent, then remove fan. Fan has lefthand handed threads.
- Loosen tensioner lock bolts, then turn tensioner with suitable wrench to receive tens...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1995 BMW 740I AUTOMOBILES
Component location diagrams for most 1995 BMW 740I cars and light trucks sold in the U.S. from 1990+.
Air Injection Pump Valve Diagram for 1995 BMW 740I 4.0 V8 GAS Components on diagram: |
Characteristic Map Sensor Diagram for 1995 BMW 740I 4.0 V8 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1995 BMW 740I AUTOMOBILES
OEM drawn wiring diagrams for most 1995 BMW 740I cars and light trucks sold in the U.S.
1995 BMW 740I 4.0 V8 GAS Wiring Diagram Components on diagram: |
1995 BMW 740I 4.0 V8 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1995 BMW 740I AUTOMOBILES
OEM TSB listings for most 1995 BMW 740I cars and light trucks sold in the U.S. from 1985+.
Document: Tools and Equipment Vehicle: 1995 BMW 740I 4.0 V8 GAS Auto Systems: |
Document: Tools and Equipment Vehicle: 1995 BMW 740I 4.0 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1995 BMW 740I AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1995 BMW 740I cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1995 BMW 740I cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1995 BMW 740I cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1995 BMW 740I cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 740I SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1995 BMW 740I vehicle. |
Access the Complete guide! |