Auto Parts Search
1993 BMW 740IL CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT BMW REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1993 BMW 740IL AUTOMOBILES
BMW -> Component Replacement & Adjustment -> EVAPORATOR TEMPERATURE SENSOR, REPLACE
Vehicle: 1993 BMW 740IL 4.0 V8 GAS
- Remove lefthand console trim panel retaining screw and set asid...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 740IL AUTOMOBILES
Disc Brakes -> Brake Pad Service -> 318 & 325 -> Except 318 & 325 -> Front Brake Pads, Replace -> Rear Brake Pads, replace
Vehicle: 1993 BMW 740IL 4.0 V8 GAS
Front Brake Pads, Replace
318 & 325
- Raise and support vehicle, then remove front wheels.
- Remove brake pad wear indicator connector from left side of caliper.
- Remove anti-rattle clip, then the caliper sliding bolt plastic caps.
- Lift brake hose out of holder, then remove caliper sliding bolts.
- Remove caliper toward rear. Remove brake pads, then suspend caliper from frame with wire.
- Reverse procedure to install, noting the following:
- Compress caliper piston into bore.
- Check fluid level and bleed brake system as necessary.
- Tighten to specifications.
Except 318 & 325
- Remove wheels and disconne...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1993 BMW 740IL AUTOMOBILES
BMW -> Fuel Filter Replacement -> Except X3 & Z4 -> Fuel System Pressure Relief -> Models w/Fitting Or Union Bolt Connection -> Models w/Fuel Hose Connection -> Removal & Installation
Vehicle: 1993 BMW 740IL 4.0 V8 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
After the battery has been disconnected and reconnected, some abnormal driveability symptoms may occur. The vehicle may need to be driven while it relearns its adaptive strategy.
Fuel System Pressure Relief
- Obtain the vehicle owner's radio theft protection code.
- Remove the fuel pump relay(s).
- Start the engine and allow it to stall.
- Crank engine for 10 seconds to ensure the fuel pressure has been...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 BMW 740IL AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 1993 BMW 740IL 4.0 V8 GAS
The propeller shaft is adapted to pertinent requirements in reverence to the transmission version, power flow and vibration behavior, so that removal and installation will differ and depend on the version. Only tighten nuts or bolts on the flange end whenever possible to avoid tension in the joint disc.
- Raise and support vehicle.
- Remove exhaust assembly.
- Unscrew heat shield.
- On models with front joint disc, unscrew propeller shaft on transmission.
- On models with front universal joint, support transmission with special tools 24 0 120 and 00 2 020.
- Unscrew transmission suspension.
- ...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1993 BMW 740IL AUTOMOBILES
Alternator, Replace -> Air Cooled -> Liquid Cooled
Vehicle: 1993 BMW 740IL 4.0 V8 GAS
Air Cooled
- Switch off ignition.
- Disconnect and cover battery ground lead.
- Remove alternator drive belt.
- Remove bolts on oil-filter housing.
- Place oil-filter housing to one side.
- Disconnect plug on alternator.
- Remove nut on alternator B+ terminal.
- Unfasten cable clip.
- Unclip cooling air guide.
- Remove alternator mounting bolts.
- Pull out alternator towards front.
- Pull alternator upwards to remove.
- Remove alternator from vehicle.
- Reverse procedure to install, noting the following:
- Torque alternator B+ terminal nut to 72 to 108 inch lbs.
- Torque alternator mounting bolts to 15 ft. lbs.
Liquid Cool...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 1993 BMW 740IL AUTOMOBILES
Cabin Air Filter Service -> BMW -> 1993-2001 7 Series
Vehicle: 1993 BMW 740IL 4.0 V8 GAS
Service interval is determined by the service indicator.
- Remove cabin air filter cover retaining screw, then open the cover.
- Depress the cabin air filter duct lock, then lift the cover upward.
- Release the cabin ai...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1993 BMW 740IL AUTOMOBILES
BMW -> Automatic Transmission Indicator Lamp ->
Vehicle: 1993 BMW 740IL 4.0 V8 GAS
The warning lamp is used to warn of a system fault. It will be lit during engine start-up, but should go out when the self-diagnostic system determines that the system is functioning properly. The warning lamp will also flash when the system ...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1993 BMW 740IL AUTOMOBILES
Radiator, Replace
Vehicle: 1993 BMW 740IL 4.0 V8 GAS
- After engine has cooled, remove expansion tank cap.
- Using pulley holding tool No. 11 5 030 or equivalent, remove engine cooling fan.
- Raise and support vehicle, then remove oil catch tray.
- Remove engine splash guard.
- Unscrew coolant drain plug and drain coolant into a suitable container.
- Disconnect coolant level sender...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1993 BMW 740IL AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1993 BMW 740IL 4.0 V8 GAS
- Remove fan cowl by lifting out expansion rivets on both sides.
- Secure fan pulley with suitable securing tool, or equivalent, then remove fan. Fan has lefthand handed threads.
- Loosen tensioner lock bolts, then turn tensioner with suitable wrench to receive tens...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1993 BMW 740IL AUTOMOBILES
Component location diagrams for most 1993 BMW 740IL cars and light trucks sold in the U.S. from 1990+.
Below LH Center Of I/P, Right Of Steering Column Diagram for 1993 BMW 740IL 4.0 V8 GAS Components on diagram: |
Instrument Panel Harness Splice Locations Diagram for 1993 BMW 740IL 4.0 V8 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1993 BMW 740IL AUTOMOBILES
OEM drawn wiring diagrams for most 1993 BMW 740IL cars and light trucks sold in the U.S.
1993 BMW 740IL 4.0 V8 GAS Wiring Diagram Components on diagram: |
1993 BMW 740IL 4.0 V8 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1993 BMW 740IL AUTOMOBILES
OEM TSB listings for most 1993 BMW 740IL cars and light trucks sold in the U.S. from 1985+.
Document: Tools and Equipment Vehicle: 1993 BMW 740IL 4.0 V8 GAS Auto Systems: |
Document: Tools and Equipment Vehicle: 1993 BMW 740IL 4.0 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1993 BMW 740IL AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1993 BMW 740IL cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1993 BMW 740IL cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1993 BMW 740IL cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1993 BMW 740IL cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 740IL SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1993 BMW 740IL vehicle. |
Access the Complete guide! |