Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1993 BMW 325I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 325I cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> 318 & 325 -> Except 318 & 325 -> Front Brake Pads, Replace -> Rear Brake Pads, replace
Vehicle: 1993 BMW 325I 2.5 L6 GAS
Front Brake Pads, Replace
318 & 325
- Raise and support vehicle, then remove front wheels.
- Remove brake pad wear indicator connector from left side of caliper.
- Remove anti-rattle clip, then the caliper sliding bolt plastic caps.
- Lift brake hose out of holder, then remove caliper sliding bolts.
- Remove caliper toward rear. Remove brake pads, then suspend caliper from frame with wire.
- Reverse procedure to install, noting the following:
- Compress caliper piston into bore.
- Check fluid level and bleed brake system as necessary.
- Tighten to specifications.
Except 318 & 325
- Remove wheels and disconne...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 325I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 325I cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description -> 735 & 750 -> 850 -> H-31 Hydraulic System -> Master Cylinder
Vehicle: 1993 BMW 325I 2.5 L6 GAS
H-31 Hydraulic System
The H-31 hydraulic system, Fig. , incorporates a power flow regulator which diverts a small flow of fluid from the power steering operating circuit for the power assisted brake system. It charges the hydraulic reservoir in a high pressure range without impairing the function of power steering. The pressurized hydraulic oil volume is supplied to the booster for the sake of power assistance and is applied by operating the connected standard tandem master cylinder. should the power steering pump fail, the hydraulic reservoir has sufficient reserve pressure to permi...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 325I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 325I cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service -> 318, 325, 525 & 535 -> 735, 750 & 850 -> Power Brake Booster, Replace
Vehicle: 1993 BMW 325I 2.5 L6 GAS
Power Brake Booster, Replace
318, 325, 525 & 535
- Remove master cylinder from booster.
- Remove lower left trim panel.
- Disconnect bayonet pin and clip from booster pushrod, below instrument panel. Fig. .
- Detach booster from pedal base. Remove booster from engine compartment.
- Reverse procedure to install.
735, 750 & 850
- With engine off, discharge hydraulic reservoir by operating brake pedal approximately 20 times with same force required for ful...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 325I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 325I cars and light trucks from 1990+.
Anti-lock Brakes -> Diagnosis & Testing -> 318 and 325 -> 525, 535, 735 & 750 -> Diagnostic Tests
Vehicle: 1993 BMW 325I 2.5 L6 GAS
The electronic control unit monitors the Anti-Lock Brake System (ABS) constantly. The system must be checked when the ABS indicator lamp does not go out, comes on while driving or does not come on when ignition is turned on. A BMW service tester ...
[[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 325I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 325I cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 1993 BMW 325I 2.5 L6 GAS
- Connect suitable pressure bleeder to brake fluid reservoir. Maximum charging pressure is 43.5 psi.
- Attach bleeder hose and container to right rear wheel. Bleed until no bubbles appear.
- Repeat step 2 for left rear, right front and left front wheels.
- Support rear suspension at wheel carriers and lower car so rear suspension compresses to its normal loaded position (to prevent damage to output shaft joints). Wheels must be able to turn freely.
- Attach...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325I BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 325I AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 BMW 325I cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Caliper Overhaul -> Caliper, Replace -> Front -> Rear
Vehicle: 1993 BMW 325I 2.5 L6 GAS
Caliper, Replace
Front
- Raise and support vehicle, then remove front wheel.
- Drain a moderate amount of brake fluid from reservoir with a syringe.
- Disconnect caliper brake hose.
- Remove caliper bolts and disconnect brake pad wear sensor electrical connector, if necessary.
- Remove caliper toward rear.
- Reverse procedure to install, noting the following:
- Tighten bolts to specifications.
- Bleed brake system.
- Ensure brake pad wear sensor wire does not contact rotor or wheel.
Rear
- Raise and support vehicle, then remove wheel.
- Drain a moderate amount of brake fluid from reservoir with a syringe.
- Disconne...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325I BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1993 BMW 325I vehicle. |
Access the Complete guide! |