Auto Parts Search
We have info for following modifications of 1990 Mitsubishi Mirage
- 1990 Mitsubishi Mirage 1.5 L4 GAS, CC:1468, CID:90, Fuel Injection, Aspiration:90, Engine VIN:, Desg:X
- 1990 Mitsubishi Mirage RS 1.5 L4 GAS, CC:1468, CID:90, Fuel Injection, Aspiration:90, Engine VIN:, Desg:X
- 1990 Mitsubishi Mirage VL 1.5 L4 GAS, CC:1468, CID:90, Fuel Injection, Aspiration:90, Engine VIN:, Desg:X
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Mitsubishi Mirage AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Mitsubishi Mirage cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1990 Mitsubishi Mirage RS 1.5 L4 GAS
- Raise and support vehicle, then remove front wheels.
- Remove cotter pin, wheel bearing nut and washer.
- Disconnect lower control arm ball joint from knuckle using tool No. MB991113 or equivalent.
- Disconnect tie rod end from knuckle using tool No. MB991113 or equivalent.
- Disconnect center bearing snap ring if equipped.
- On models without center bearing, proceed as follows:
- Insert pry bar between transaxle case and driveshaft, then pry driveshaft from transaxle. Do not pull on driveshaft, or insert pry bar deep enough to damage oil seal.
- Remove driveshaft from hub using tool No. MB99...
CLICK HERE TO GET FULL ACCESS TO 1990 Mitsubishi Mirage DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Mitsubishi Mirage AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Mitsubishi Mirage cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1990 Mitsubishi Mirage VL 1.5 L4 GAS
- Raise and support vehicle, then remove front wheels.
- Remove cotter pin, wheel bearing nut and washer.
- Disconnect lower control arm ball joint from knuckle using tool No. MB991113 or equivalent.
- Disconnect tie rod end from knuckle using tool No. MB991113 or equivalent.
- Disconnect center bearing snap ring if equipped.
- On models without center bearing, proceed as follows:
- Insert pry bar between transaxle case and driveshaft, then pry driveshaft from transaxle. Do not pull on driveshaft, or insert pry bar deep enough to damage oil seal.
- Remove driveshaft from hub using tool No. MB99...
CLICK HERE TO GET FULL ACCESS TO 1990 Mitsubishi Mirage DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Mitsubishi Mirage AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Mitsubishi Mirage cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1990 Mitsubishi Mirage 1.5 L4 GAS
- Raise and support vehicle, then remove front wheels.
- Remove cotter pin, wheel bearing nut and washer.
- Disconnect lower control arm ball joint from knuckle using tool No. MB991113 or equivalent.
- Disconnect tie rod end from knuckle using tool No. MB991113 or equivalent.
- Disconnect center bearing snap ring if equipped.
- On models without center bearing, proceed as follows:
- Insert pry bar between transaxle case and driveshaft, then pry driveshaft from transaxle. Do not pull on driveshaft, or insert pry bar deep enough to damage oil seal.
- Remove driveshaft from hub using tool No. MB99...
CLICK HERE TO GET FULL ACCESS TO 1990 Mitsubishi Mirage DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1990 Mitsubishi Mirage vehicle. |
Access the Complete guide! |