Auto Parts Search
We have info for following modifications of 1990 Dodge Ramcharger
- 1990 Dodge Ramcharger 5.2 V8 GAS, CID:318, Fuel Injection, Aspiration:318, Engine VIN:, Desg:Y
- 1990 Dodge Ramcharger 5.9 V8 GAS, CID:360, Fuel Injection, Aspiration:360, Engine VIN:, Desg:Z
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Dodge Ramcharger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Dodge Ramcharger cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1990 Dodge Ramcharger 5.9 V8 GAS
Front
- Position transmission and transfer case to their neutral positions. Raise and support vehicle. Remove skid plate, if equipped.
- Mark a line across transfer case flange and CV for installation reference.
- Mark a line across propeller shaft flange yoke and front axle companion flange for installation reference.
- Remove companion flange bolts.
- Remove transfer case flange bolts and remove propeller shaft.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Torque companion flange and flange yoke bolts to 80 ft. lbs.
- Torque transfer case companion flange bolts to...
CLICK HERE TO GET FULL ACCESS TO 1990 Dodge Ramcharger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Dodge Ramcharger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Dodge Ramcharger cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> U-Joint with Injected Rings -> U-Joint with Snap Rings
Vehicle: 1990 Dodge Ramcharger 5.9 V8 GAS
This procedure describes a propeller shaft equipped with a cardan joint in the tube yoke. For propeller shafts equipped with a companion/slip yoke, repeat the steps to remove the remaining cardan joint.
U-Joint with Snap Rings
Disassemble
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke.
- Position yoke with grease fitting if equipped, pointing up.
- Position a socket with a inside diameter large enough to receive bearing cap, beneath yoke on a press.
- Place another socket with an outside diameter smaller than bearing cap on ...
CLICK HERE TO GET FULL ACCESS TO 1990 Dodge Ramcharger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Dodge Ramcharger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Dodge Ramcharger cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> U-Joint with Injected Rings -> U-Joint with Snap Rings
Vehicle: 1990 Dodge Ramcharger 5.2 V8 GAS
This procedure describes a propeller shaft equipped with a cardan joint in the tube yoke. For propeller shafts equipped with a companion/slip yoke, repeat the steps to remove the remaining cardan joint.
U-Joint with Snap Rings
Disassemble
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke.
- Position yoke with grease fitting if equipped, pointing up.
- Position a socket with a inside diameter large enough to receive bearing cap, beneath yoke on a press.
- Place another socket with an outside diameter smaller than bearing cap on ...
CLICK HERE TO GET FULL ACCESS TO 1990 Dodge Ramcharger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Dodge Ramcharger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1990 Dodge Ramcharger cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1990 Dodge Ramcharger 5.2 V8 GAS
Front
- Position transmission and transfer case to their neutral positions. Raise and support vehicle. Remove skid plate, if equipped.
- Mark a line across transfer case flange and CV for installation reference.
- Mark a line across propeller shaft flange yoke and front axle companion flange for installation reference.
- Remove companion flange bolts.
- Remove transfer case flange bolts and remove propeller shaft.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Torque companion flange and flange yoke bolts to 80 ft. lbs.
- Torque transfer case companion flange bolts to...
CLICK HERE TO GET FULL ACCESS TO 1990 Dodge Ramcharger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1990 Dodge Ramcharger vehicle. |
Access the Complete guide! |